| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: dwmac1000: clear the RGMII status interrupt
Since commit 2e2c878a3141 ("net: stmmac: remove SGMII/RGMII/SMII
interrupt handling") nothing on the RGMII path reads GMAC_RGSMIIIS, so
RGSMIIIS stays pending behind GMAC_INT_MASK from the first link change
on. stmmac_resume() resets the MAC in stmmac_hw_setup(); the reset sets
GMAC_INT_MASK to 0 until dwmac1000_core_init() writes the mask again,
and the pending status storms the line:
dwmac_dma_interrupt: unexpected status 04000000
A register dump at the first message on ODROID-HC4 showed it:
core int_status 00000001 int_mask 00000000 pmt 00000000 rgsmiiis 0000000d
When the resume thread runs on the CPU that takes the MAC interrupt,
the storm starves it: a soft lockup, then a watchdog reset or a hang.
Read GMAC_RGSMIIIS in dwmac1000_irq_status() when the status is not
masked, as the driver did before 2e2c878a3141; the read clears it.
Wake-on-LAN resume from s2idle with the resume thread and the MAC
interrupt on one CPU: Helios64 (dwmac-rk), 7.3-rc6, soft-locked in 3 of
3 resumes without a fix and in 0 of 10 with this patch; it ran with an
out-of-tree dwmac-rk change that keeps the GMAC powered across suspend.
ODROID-HC4 (dwmac-meson8b): 0 of 10 with this patch, 2 of 2 without a
fix on a 7.3-rc5 build. irq_rgmii_n went up by one per resume. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Mark sched_process_wait argument as nullable
do_wait() passes wo->wo_pid to the sched_process_wait tracepoint.
kernel_wait4() leaves wo_pid NULL for wait4(-1), and
kernel_waitid_prepare() does likewise for waitid(P_ALL).
btf_ctx_access() currently types argument 0 as PTR_TO_BTF_ID |
PTR_TRUSTED. Without PTR_MAYBE_NULL, the verifier accepts an unchecked
dereference. Trusted pointer loads have no fault protection, so a wait for
any child can then cause a NULL pointer dereference in JITed BPF code.
Add sched_process_wait to raw_tp_null_args[] with argument 0 marked
nullable. The verifier rejects an unchecked dereference while preserving
access after the program checks the pointer for NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: skbuff: preserve shared-frag marker during coalescing
skb_try_coalesce() can attach paged frags from @from to @to. If @from
has SKBFL_SHARED_FRAG set, the resulting @to skb can contain the same
externally-owned or page-cache-backed frags, but the shared-frag marker
is currently lost.
That breaks the invariant relied on by later in-place writers. In
particular, ESP input checks skb_has_shared_frag() before deciding
whether an uncloned nonlinear skb can skip skb_cow_data(). If TCP
receive coalescing has moved shared frags into an unmarked skb, ESP can
see skb_has_shared_frag() as false and decrypt in place over page-cache
backed frags.
Propagate SKBFL_SHARED_FRAG when skb_try_coalesce() transfers paged
frags. The tailroom copy path does not need the marker because it copies
bytes into @to's linear data rather than transferring frag descriptors. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: move attribute payload before shrinking its record
ntfs_new_attr_flags() resizes the non-resident attribute record before
moving its name and mapping pairs to their shorter-header offsets when
compression or sparse state is cleared.
Shrinking the record first moves the following attribute over the tail of
the old record. The subsequent memmove() therefore copies bytes from that
following attribute instead of the old mapping pairs. Re-enabling
compression on an empty file persists those bytes as a malformed mapping
pairs array, which ntfsck reports as a missing or invalid run length.
Move the payload before shrinking the record, while retaining the existing
resize-before-move ordering when growing it. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix the bypass dispatch claim for schedulers bypassed by an ancestor
scx_bypass() claims bypass dispatch when the scheduler's depth goes from
zero to one and releases it when the depth returns to zero, but propagates
only the depth to the descendants, not the claim. A descendant that starts
bypassing with its ancestor never claims, and one whose own bypass ends
under the ancestor's keeps its claim, as its depth does not return to zero.
A sub-scheduler enable whose bypass ends under a PM suspend thus leaks its
claim: the parent keeps hosting bypass dispatch and the sub-scheduler's next
bypass trips the WARN_ON_ONCE() on the claim. A sub-scheduler disable that
starts under a PM suspend has no claim, so once the resume lifts the root's
bypass its tasks sit on the parent's bypass DSQs with nobody consuming them.
Claim for every descendant whose depth goes from zero to one in the
propagation and release every scheduler in the subtree whose depth returned
to zero once the tasks have moved out of the bypass DSQs. A parent that is
bypassing itself when a descendant claims consumes only its own bypass DSQs,
empty until it leaves bypass and becomes the host. |
| In the Linux kernel, the following vulnerability has been resolved:
ipc: drop the mqueue mount with kern_unmount() on setup failure
mq_init_ns() creates the mqueue mount with fc_mount_longterm(), so its
->mnt_ns is MNT_NS_INTERNAL. When setting up the mqueue or ipc sysctls
or msg_init_ns() fails afterwards, create_ipc_ns() drops it with a plain
mntput(). With ->mnt_ns set that takes the fast path of
mntput_no_expire(). The count drops to zero and nothing ever kills the
mount, so the mount and the mqueue superblock are leaked.
Commit dc55e35f9e81 ("ipc: Store mqueue sysctls in the ipc namespace")
added the first failure path after mq_init_ns() and never dropped the
mount. Commit 7229d74e5e8c ("ipc: create_ipc_ns: drop mqueue mount on
sysctl setup failure") tried to fix that with a mntput() but that
doesn't help for a long-term mount.
Use kern_unmount(). free_ipc() open-codes the same thing for a namespace
that made it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hisilicon: hip04_eth: Move setting of netops to fix crash
hip04_mac_probe() calls of_phy_connect() before ndev->netdev_ops is
assigned. phy_attach_direct() -> phy_link_topo_add_phy() reads
dev->netdev_ops through netdev_need_ops_lock() since the commit in
question, so probing crashes with a NULL pointer dereference when
CONFIG_NET_SHAPER is enabled.
Assign netdev_ops before the PHY attach, as was done for emac in commit
7c9f391ec89c ("net: emac: move setting of netops to fix crash"). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Disable interrupts while holding delayed_cmd_lock
target_do_delayed_work() takes dev->delayed_cmd_lock with a plain
spin_lock(). It runs from system_percpu_wq, so interrupts stay enabled
while the lock is held. Every other acquisition of that lock uses
spin_lock_irqsave(): target_handle_task_attr() and
transport_complete_ordered_sync() in target_core_transport.c, and
target_non_ordered_release() in target_core_device.c.
That was safe while every caller of transport_complete_task_attr() ran
in process context: target_complete_ok_work() from target_completion_wq,
transport_complete_qf() from dev->qf_work_queue, and
transport_generic_request_failure() from the submit and execute paths.
Since commit 06933066d88a ("scsi: target: Add support for completing
commands from backend context") that is no longer true. With
complete_type=1 on a fabric that sets direct_compl_supp,
target_complete() runs target_complete_ok_work() inline in the backend's
completion context, which target_complete_cmd_with_sense() documents as
"May be called from interrupt context". For iblock that is the bio
end_io.
target_complete_ok_work() starts with transport_complete_task_attr(),
which takes delayed_cmd_lock in two ways:
- Every ORDERED command is put on dev->delayed_cmd_list by
target_handle_task_attr() and dispatched from there by
target_do_delayed_work(), which marks it SCF_TASK_ORDERED_SYNC. Its
completion therefore goes through transport_complete_ordered_sync().
- A SIMPLE command that completes while an ORDERED command is pending
drops the last reference to the killed dev->non_ordered, and
percpu_ref_put() then runs target_non_ordered_release() in the
completing context.
Both take the lock and, if commands are waiting, call
schedule_work(&dev->delayed_cmd_work), which queues on system_percpu_wq,
i.e. on the CPU that took the completion. Further completions for the
same queue are typically delivered there too, so one arriving while the
work holds the lock spins on it forever.
Reaching this needs complete_type=1, which is not the default
(vhost-scsi, the only fabric with direct_compl_supp, defaults to
TARGET_QUEUE_COMPL), a backend whose I/O completes from interrupt
context, and ORDERED commands from the initiator. Linux virtio_scsi
guests send only VIRTIO_SCSI_S_SIMPLE and never take the ordered path;
any guest that uses the ORDERED task attribute, which vhost-scsi
accepts, does.
target_do_delayed_work() is a work item and always runs in process
context, so spin_lock_irq() is sufficient.
Found by inspection; no runtime report. A single ORDERED command goes
through both acquisitions, so with CONFIG_PROVE_LOCKING the first one
completed through direct completion should produce an inconsistent lock
state report on delayed_cmd_lock (hardirq or softirq, depending on where
the backend completes). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/oa: Zero OA buffer at allocation
ttm_bo_type_kernel BOs are not guaranteed to be zeroed on allocation and
may contain data from previously freed pages. Since the OA buffer is
mmap'able by userspace, this can expose stale kernel memory contents.
Streams opened with DRM_XE_OA_PROPERTY_OA_DISABLED allocate the OA
buffer without calling xe_oa_init_oa_buffer(). Zero the buffer at
allocation to prevent information disclosure through mmap.
The existing zeroing in xe_oa_init_oa_buffer() remains necessary for
zero report-id/timestamp detection on enable/re-enable.
(cherry picked from commit 126c4c5388f9311a390b9b254a835b0cf0f55331) |
| In the Linux kernel, the following vulnerability has been resolved:
accel/rocket: clear rdev on device init failure
rocket_probe() stores the return value from rocket_device_init() in the
file-scoped rdev pointer before checking whether it is an error pointer.
If rocket_device_init() fails, rdev is left as an ERR_PTR.
The rdev pointer is also used as the marker for whether the shared rocket
device has already been initialized. A later core probe can therefore see
a non-NULL rdev, skip rocket_device_init(), and dereference the error
pointer when reading rdev->num_cores.
Save the error code and clear rdev before returning from the
rocket_device_init() failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: fix FITRIM range alignment
ntfs_trim_fs() aligns the start of a free extent up to the device discard
granularity, but derives the discard length by aligning the original extent
length down. When the free extent start is not discard-aligned, adding that
length to the aligned start can extend the discard past the free extent and
into allocated clusters.
For example, with 4 KiB clusters and 32 KiB discard granularity, the free
extent [4 KiB, 36 KiB) becomes the discard range [32 KiB, 64 KiB), so
28 KiB beyond the free extent may be discarded.
Align the absolute end of the free extent down and derive the length from
the two aligned endpoints. Skip extents that contain no full discard unit.
Reproduced with a 4 KiB-cluster NTFS filesystem on scsi_debug configured
for 32 KiB discard granularity and read-zero-after-trim. Before this
change, FITRIM zeroed seven allocated 4 KiB clusters following an unaligned
32 KiB hole. With this change, the same data remains intact across FITRIM
and remount. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject SetEA requests that do not fit the request buffer
CIFSSMBSetEA() copies the caller's extended attribute value into the
SMB request buffer without checking that it fits. The requirement is
stated in the source but was never implemented:
/*BB add length check to see if it would fit in
negotiated SMB buffer size BB */
/* if (ea_value_len > buffer_size - 512 (enough for header)) */
if (ea_value_len)
memcpy(parm_data->list.name + name_len + 1,
ea_value, ea_value_len);
The only bound applied on the way in is in cifs_xattr_set():
#define MAX_EA_VALUE_SIZE CIFSMaxBufSize
...
if (size > MAX_EA_VALUE_SIZE)
CIFSMaxBufSize is the full payload capacity of the buffer, so a value
of exactly that size leaves no room for the SMB header, the TRANS2
parameter block, the fealist header and the EA name that are written
ahead of it in the same object.
SendReceive() already enforces the correct limit on this very length:
if (in_len > CIFSMaxBufSize + MAX_CIFS_HDR_SIZE)
but it is called after the copy has taken place. An unprivileged
setxattr(2) on an SMB1 mount with a 250-byte name and a 16384-byte
value writes 16384 bytes starting 345 bytes into a 16588-byte
cifs_request object, ending 141 bytes past it:
BUG: KASAN: slab-out-of-bounds in CIFSSMBSetEA+0xabc/0xde0
Write of size 16384 at addr ffff888003aa0159 by task init/68
__asan_memcpy+0x3c/0x60
CIFSSMBSetEA+0xabc/0xde0
cifs_xattr_set+0xd3a/0xff0
__vfs_setxattr+0x13e/0x1a0
The buggy address is located 345 bytes inside of
allocated 16588-byte region
Apply SendReceive()'s limit to the assembled request before the copy
rather than after it, and widen the byte counters so the sum cannot
wrap before it is tested.
byte_count is also tested against U16_MAX, because it is stored in the
16-bit pSMB->ByteCount. That becomes reachable when CIFSMaxBufSize is
raised at module load, where it may be set as high as 1024*127: with a
5-byte EA name and a 65521-byte value, count is exactly U16_MAX while
byte_count is 65556, and cpu_to_le16() would truncate it to 20 and
transmit a frame whose ByteCount does not match its length. Testing
byte_count covers count as well, since byte_count is the larger of the
two and count's only 16-bit consumer is written after this point.
check_add_overflow() is evaluated first so that total_len is assigned
before it is reported. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix data corruption with concurrent writes and O_TRUNC
cifs_do_truncate() flushes dirty pages with filemap_write_and_wait()
and truncates the file on the server, but in the old code both
operations ran without holding i_rwsem or invalidate_lock. A
concurrent buffered write via netfs_perform_write() -- which only
needs i_rwsem shared -- could dirty new pages after the flush but
before the local truncation, and those pages would be silently
discarded by cifs_setsize() -> truncate_pagecache().
Fix by acquiring inode_lock (exclusive i_rwsem) and
filemap_invalidate_lock at the top of cifs_do_truncate(), so the
entire flush-truncate-resize sequence is atomic with respect to:
- buffered writes (blocked by exclusive i_rwsem, since
netfs_start_io_write takes i_rwsem shared),
- read page faults (blocked by exclusive invalidate_lock, since
filemap_fault takes it shared),
- writeback collection (blocked by netfs_wb_begin/netfs_wb_end
around the server truncate and local resize, since
netfs_writepages also acquires the wb lock). |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: futex: untag the user pointer before the atomic access
access_ok() checks untagged_addr(uaddr), but arch_futex_atomic_op_inuser()
and futex_atomic_cmpxchg_inatomic() hand the raw uaddr to the inline asm
amoswap/amoadd/.../lr.w+sc.w through the "+m" (*uaddr) operand. When the
tagged address ABI is enabled (CONFIG_RISCV_ISA_SUPM, prctl
PR_SET_TAGGED_ADDR_CTRL with PMLEN != 0), those two addresses differ: a
user pointer whose top PMLEN bits hold a tag passes access_ok() after
untagging, but the atomic is then performed on the still-tagged raw
address.
Supervisor-mode data accesses are not subject to the U-mode pointer
masking (that is governed by menvcfg.PMM, which the kernel does not set),
so hardware does not strip the tag for the kernel's own access. With
Sv57 and PMLEN=16 the tag bits overlap the canonical-address bits, so a
tagged pointer can name a canonical kernel virtual address (e.g. in the
linear map) whose untagged form is a valid user address. An unprivileged
process can thus make FUTEX_WAKE_OP perform an atomic read-modify-write on
an arbitrary kernel address, with the matching FUTEX_OP_CMP_* result
serving as a read oracle.
get_user()/put_user()/raw_copy_{to,from}_user() already untag the pointer
after the access_ok() check; do the same in the futex helpers so the
atomic operates on the address that was actually validated. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: of: fill in supply names in of_regulator_bulk_get_all()
of_regulator_bulk_get_all() returns an array it allocated itself, and
fills in only the consumer of each entry. Every other way of getting a
bulk array has the supply name set, because the caller provides it, and
the core expects it to be there: regulator_bulk_enable() prints it when
a supply fails to enable, so a caller that hands such an array to it
dereferences uninitialised memory on that path.
Copy each name into the array's own allocation, right behind the
entries, so that it shares the array's lifetime and callers still have
nothing extra to free. That also retires the fixed 64 byte stack buffer
the names were assembled in, which is_supply_name() never bounded the
copy against. |
| In the Linux kernel, the following vulnerability has been resolved:
power: sequencing: pcie-m2: Fix leaking array from of_regulator_bulk_get_all()
of_regulator_bulk_get_all() allocates the consumers array and hands it to
the caller, who is expected to free it at an appropriate time.
pwrseq-pcie-m2.c never did, leading to a memory leak.
Add an explicit kfree() for the consumers array. |
| In the Linux kernel, the following vulnerability has been resolved:
net: team: free skb when broadcast has no txable port
bc_transmit() sends the original skb through the last txable port.
When no port is txable, it returns false without consuming the skb, but
team_xmit() still returns NETDEV_TX_OK. AF_PACKET sends then retain the
skb and its socket write-memory charge.
A TX-enabled, link-down port keeps the broadcast transmit op installed.
Carrier can stay up through a second link-up, TX-disabled port or be
forced on by userspace. Free the original skb on the no-port path while
leaving the existing drop accounting intact.
Discovered by Sashiko during review of previous commit. |
| In the Linux kernel, the following vulnerability has been resolved:
net: skbuff: don't leave stale bytes in skb_copy_and_csum_bits()
When skb_copy_and_csum_bits() reaches unreadable frags it returns 0
after copying only the linear part, and the rest of the caller's buffer
is left as it was. The callers copy into a buffer that is about to go
out on the wire: an ICMP error quoting the offending packet, or a
driver's TX bounce buffer in skb_copy_and_csum_dev(). Neither buffer
is zeroed beforehand, so whatever was in memory there gets sent.
Zero the part of the buffer we didn't fill. The checksum usually
won't match the data any more, so the receiver will usually drop the
packet, but either way it no longer carries anything it shouldn't.
Only zero for a positive @len, a negative one from a broken caller must
not turn into a huge memset(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: disable rx napi when removing device
Unloading the mt7915e module with a MT7916 triggers multiples WARN in
__netif_napi_del_locked() and in page_pool_disable_direct_recycling()
because the driver does not disable the napi before destroying it.
This is troublesome since on MT7916 it is required to unload the module
and reinsert it with a different enable_6ghz parameter to change the
frequency. The system generally becomes unstable after reinserting the
module.
Fix it by disabling rx napi inside mt7915e itself, even through napi rx is
enabled in the mt76 generic code. Disabling it in the mt76 generic code
was previously attempted and reverted because napi was disabled too
late and rx handlers could access freed structures. Note that the tx
side is enabled and disabled by the mt76 generic code.
It is disabled in mt7915_stop_hardware() since, unlike
mt7915_unregister_device(), is it also called in the probe path if an
error happens after rx napi is enabled. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: account non-AQL frames per peer rather than per link
The driver increments wcid->non_aql_packets when a frame goes to the
hardware queue. The completion path decrements the counter again.
For an MLO peer, the hardware reports the completion on the link that it
used for the transmission. This link can differ from the link that the
driver queued the frame on. In that case, the increment and the
decrement go to different link wcids, and the count drifts upwards until
it blocks the station.
Keep the count on the wcid of the primary link, like the other peer-wide
state. |
