| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: do not propagate one-packet flag to synced conns
Synced connections can be created before their destination exists. When
the destination is later added, ip_vs_bind_dest() copies connection flags
from the destination into cp->flags.
IP_VS_CONN_F_ONE_PACKET connections are not synced. If a synced
connection inherits IP_VS_CONN_F_ONE_PACKET while it is already hashed,
expiry can treat it as a one-packet connection and skip unlinking the
existing conn_tab node, leaving stale hash nodes pointing at a freed
struct ip_vs_conn.
Drop IP_VS_CONN_F_ONE_PACKET from destination flags when binding synced
connections. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: re-fetch eth header after route_shortcircuit()
Before route_shortcircuit(), the eth header pointer is cached from eth_hdr(skb).
Inside route_shortcircuit(), pskb_may_pull() can be called, which may
reallocate skb->head.
In this case, returning to vxlan_xmit() leaves the cached eth pointer pointing to
freed memory, leading to a use-after-free when dereferencing eth->h_dest.
Fix this by updating eth = eth_hdr(skb) after calling route_shortcircuit(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ebt_nflog: pin the NFLOG backend
nf_log_unregister() runs after the per-net teardown so its final RCU
grace period also drains readers that obtained the logger from a per-net
binding. However, ebt_nflog passes an explicit ULOG log type to
nf_log_packet() without holding a reference on the selected logger module,
unlike the xt_NFLOG and nft_log frontends.
An ebtables nflog rule can therefore remain callable while nfnetlink_log
is unloaded. The resulting interleaving is:
CPU 0 CPU 1
nfnetlink_log_fini()
unregister_pernet_subsys()
kfree(nfnl_log_pernet(net))
ebt_nflog_tg()
nf_log_packet()
nfulnl_log_packet()
instance_lookup_get_rcu()
The global ULOG logger is still registered at this point, so CPU 1
dereferences the per-net state after CPU 0 has freed it. KASAN reported:
BUG: KASAN: slab-use-after-free in instance_lookup_get_rcu
Read of size 8 at addr ff110001052e6210 by task poc/92
Call Trace:
instance_lookup_get_rcu+0x1ce/0x1f0 [nfnetlink_log]
nfulnl_log_packet+0x248/0x2fb0 [nfnetlink_log]
nf_log_packet+0x204/0x300
ebt_nflog_tg+0x351/0x550
ebt_do_table+0xedf/0x22b0
Allocated by task 90:
__kmalloc_noprof+0x186/0x470
ops_init+0x6d/0x420
register_pernet_operations+0x2f6/0x670
register_pernet_subsys+0x23/0x40
Freed by task 93:
kfree+0x131/0x3c0
ops_undo_list+0x3e3/0x700
unregister_pernet_operations+0x232/0x490
unregister_pernet_subsys+0x1c/0x30
nfnetlink_log_fini+0x34/0x450 [nfnetlink_log]
Acquire the ULOG logger module reference when an ebt_nflog rule is
validated and release it when the rule is destroyed. Request the NFLOG
backend for legacy callers when needed, matching xt_NFLOG. This prevents
module teardown until all ebt_nflog rules have stopped using the logger. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Fix group leader use-after-free after sibling detach
perf_group_detach() handles leader and sibling detach differently. When the
group leader is detached, all siblings are promoted to singleton events and
their group_leader pointer is reset to themselves. When a sibling is
detached, it is removed from the leader's sibling_list, but its
group_leader pointer is left pointing at the old leader.
That is harmless when the sibling is being closed and freed immediately, as
in the DETACH_DEAD path. It is not safe when the sibling is detached but
kept alive, such as during CPU hotplug with DETACH_GROUP. In that case the
sibling is removed from the context, while its file descriptor can still
keep it alive.
A typical failing sequence is:
- A group contains leader L and sibling S.
- CPU hot-unplug detaches S with DETACH_GROUP, removing it from
L->sibling_list but leaving S->group_leader == L.
- L is later closed and freed.
- A PERF_IOC_FLAG_GROUP ioctl on S follows S->group_leader and
dereferences the freed leader.
This was reproduced by running the perf event fuzzer, CPU hotplug, and a
stress workload concurrently:
Unable to handle kernel paging request at virtual address 006b6b6b6b6b6cdb
CPU: 2 PID: 12489 Comm: perf_fuzzer 6.18.7 PREEMPT
pc : perf_ioctl+0x34c/0xc68
x20: ffffff89a3fa2c70 x8 : 6b6b6b6b6b6b6b6b
Code: 943c4a0e 340047a0 f9404a94 f9411e88 (f940b908)
Call trace:
perf_ioctl+0x34c/0xc68 (P)
__arm64_sys_ioctl+0xa0/0xf4
invoke_syscall+0x58/0xe4
el0_svc_common+0xa8/0xdc
do_el0_svc+0x1c/0x28
el0_svc+0x40/0xc0
el0t_64_sync_handler+0x68/0xdc
el0t_64_sync+0x1c4/0x1c8
The fault happened in perf_ioctl(), where perf_event_for_each() follows
the stale group_leader pointer and perf_event_for_each_child() then
dereferences the freed leader's context.
Fix the use-after-free by promoting the detached sibling to a singleton.
Also fix __event_disable() cgroup accounting and event state change. |
| In the Linux kernel, the following vulnerability has been resolved:
net: smc: fix splice entry lifetime imbalance in smc_rx_splice
smc_rx_splice() passes pages to splice_to_pipe() before taking the
references that cover the lifetime of each splice entry. In the
VM-backed RMB path, splice_to_pipe() may drop unqueued entries through
smc_rx_spd_release(), while queued entries are released later via the
pipe buffer callback.
The old post-splice accounting also derives the number of queued VM pages
from an offset mutated while building the descriptor, and a multi-page
splice pairs one sock_hold() with multiple sock_put() calls.
Take the page and socket references for every candidate entry before
splice_to_pipe(), and drop the matching private state, page reference,
and socket reference from smc_rx_spd_release() for entries that never
get queued. This fixes a refcount imbalance that can underflow page
refcounts and trigger a use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv6: clear suppressed fib6 rule result
fib6_rule_suppress() drops a suppressed route with ip6_rt_put_flags(),
but leaves res->rt6 pointing at the released rt6_info.
If no later rule supplies a replacement, fib6_rule_lookup() still sees
res.rt6 and returns that stale dst to its caller. A suppressing rule can
therefore leak a released route back to rt6_lookup(), and the next put
hits rcuref_put_slowpath() from dst_release().
Clear res->rt6 when suppressing the route so suppressed lookups fall
through to the null dst instead of reusing the released one. |
| In the Linux kernel, the following vulnerability has been resolved:
fou: Fix use-after-free in fou_create()
fou_create() publishes struct fou through sk_user_data before adding the
new FOU port to the per-netns list. If fou_add_to_port_list() fails,
the error path frees fou while it is still reachable through
sk_user_data. A concurrent receive can then dereference the freed
object in fou_from_sock().
This ordering issue was previously noted in the linked discussion.
The failure is reachable when local port 0 is requested. Each socket
binds to a different ephemeral port, but fou_cfg_cmp() compares the
requested port 0 and reports -EALREADY once an entry already exists.
Release the tunnel socket before freeing fou so sk_user_data is cleared
first, and defer reclamation with kfree_rcu() to protect concurrent RCU
readers. This matches the lifetime handling in fou_release(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix tid_tx use-after-free on BA session stop
ieee80211_stop_tx_ba_cb() hands tid_tx to kfree_rcu() through
ieee80211_remove_tid_tx(), and then reads tid_tx->ndp after dropping
sta->lock:
ieee80211_remove_tid_tx(sta, tid); /* kfree_rcu(tid_tx, rcu_head) */
...
spin_unlock_bh(&sta->lock);
if (start_txq)
ieee80211_agg_start_txq(sta, tid, false);
if (send_delba)
ieee80211_send_delba(..., tid_tx->ndp);
That read is not covered by an RCU read-side critical section, and it runs
in preemptible process context: both callers hold the wiphy mutex, reaching
it either from the ieee80211_ba_session_work() wiphy work or from
ieee80211_sta_tear_down_BA_sessions() during station teardown.
Softirqs can run in that window too, both from the local_bh_enable() that
ends ieee80211_agg_start_txq() and from any interrupt exit, so the RCU
callback can free tid_tx before the read.
Driving the function from a test module with the grace period forced into
that window, KASAN reports the read, and the free arrives on the ordinary
RCU softirq path:
BUG: KASAN: slab-use-after-free in ieee80211_stop_tx_ba_cb+0x3cd/0x400
Read of size 1 at addr ffff888002b9f52e by task kworker/0:1/10
[...]
Freed by task 57:
__kasan_slab_free+0x47/0x70
__rcu_free_sheaf_prepare+0x70/0x250
rcu_free_sheaf_nobarn+0x18/0x40
rcu_core+0x426/0x1310
handle_softirqs+0x144/0x590
__irq_exit_rcu+0xea/0x150
irq_exit_rcu+0x9/0x20
sysvec_apic_timer_interrupt+0x6b/0x80
asm_sysvec_apic_timer_interrupt+0x1a/0x20
send_delba is only set when tx_stop is set, which happens for
AGG_STOP_LOCAL_REQUEST alone, so this is reached on local teardown -
session idle timeout, PTK rekey, suspend, HW reconfig - and not from a
peer's DELBA.
Read ndp into a local before the session is freed, while sta->lock is still
held. tid_tx->ndp has a single writer, in
ieee80211_tx_ba_session_handle_start(), which cannot run concurrently here:
both paths are serialised by the wiphy mutex, and the session is already
marked HT_AGG_STATE_STOPPING at this point. tid_tx->ndp is also the only
tid_tx dereference left after ieee80211_remove_tid_tx() in this function.
[move/change the comment a bit to be more general not just on ndp,
initialize ndp directly] |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix potential UAF on meter attach failure
While attaching a newly created meter attach_meter() function makes
the new meter visible to other CPUs but can still fail afterwards.
On failure, it detaches the meter back and returns an error.
However, this is an unexpected behavior for the ovs_meter_cmd_set()
that uses a plain kfree(meter) on attach failure without waiting for
RCU readers to stop using it, assuming it was never visible.
This is never a problem for ovs-vswitchd as it always creates meters
before creating any flows that use them. But the UAF can be triggered
with a custom application using uAPI:
BUG: KASAN: slab-use-after-free in ovs_meter_execute (net/openvswitch/meter.c:653)
Read of size 8 at addr ffff88810d152650 by task meter/2508
Call Trace:
ovs_meter_execute (net/openvswitch/meter.c:653)
do_execute_actions (net/openvswitch/actions.c:1407)
ovs_execute_actions (net/openvswitch/actions.c:1584)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:703)
...
netlink_sendmsg (af_netlink.c:1900)
Allocated by task 2519:
__kasan_kmalloc (mm/kasan/common.c:398 mm/kasan/common.c:415)
ovs_meter_cmd_set (net/openvswitch/meter.c:422)
...
netlink_sendmsg (af_netlink.c:1900)
Freed by task 2519:
kfree (mm/slub.c:2705 mm/slub.c:6405 mm/slub.c:6720)
ovs_meter_cmd_set (net/openvswitch/meter.c:479)
...
netlink_sendmsg (af_netlink.c:1900)
Fix that by making sure attach_meter() doesn't make the meter visible
until all the checks are done and the function can't fail anymore.
This also makes sure the "hash" value is calculated after the potential
re-sizing of the table.
Reported by Trend Micro's Zero Day Initiative as ZDI-CAN-31642. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: Cancel hrtimer before clearing slave pointer
In i2c_imx_unreg_slave(), the slave pointer is set to NULL after
disabling interrupts. However, a pending interrupt might already
have started the hrtimer (i2c_imx_slave_timeout) before the pointer
was cleared. If the hrtimer fires after i2c_imx->slave is set to
NULL, the timer callback i2c_imx_slave_finish_op() will call
i2c_imx_slave_event() with a NULL slave pointer, which results in a
use-after-free / NULL pointer dereference.
Fix by canceling the hrtimer and waiting for it to complete after
disabling interrupts, before clearing the slave pointer. |
| Use after free in Microsoft Office Excel allows an unauthorized attacker to execute code over a network. |
| Use after free in Microsoft Office Excel allows an unauthorized attacker to execute code over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: pin svc_xprt across the asynchronous TLS handshake callback
svc_tcp_handshake() stores the raw svc_xprt pointer in
tls_handshake_args.ta_data and submits the request through
tls_server_hello_x509(). The handshake core takes only
sock_hold(req->hr_sk); nothing references the embedding struct
svc_sock that svc_tcp_handshake_done() reaches via container_of().
Two close races leave the in-flight callback writing through a freed
svc_sock. svc_sock_free() calls tls_handshake_cancel() and discards
its return value: a false return means handshake_complete() has
already set HANDSHAKE_F_REQ_COMPLETED but hp_done() may not have
finished, yet svc_sock_free() proceeds to kfree(svsk). The
cancel-loser fall-through inside svc_tcp_handshake() itself produces
the same window: when wait_for_completion_interruptible_timeout()
returns <= 0 (timeout or signal) and tls_handshake_cancel() returns
false, the function does not drain, returns, and svc_handle_xprt()
calls svc_xprt_received(), which clears XPT_BUSY and can drop the
last reference. A concurrent close then runs svc_sock_free() while
svc_tcp_handshake_done() is still updating xpt_flags and walking
svsk->sk_handshake_done.
The corruption surfaces as set_bit/clear_bit RMW into the freed
xpt_flags slab slot and as complete_all() walking and writing the
freed wait_queue_head_t list embedded in sk_handshake_done -- a
slab-corruption primitive, not a benign read. The path is reachable
on any TLS-enabled NFS server whenever a connection close overlaps
the tlshd downcall delivery window; the interruptible wait means
signal delivery suffices, not just SVC_HANDSHAKE_TO expiry.
Take svc_xprt_get(xprt) immediately before tls_server_hello_x509()
so the in-flight callback owns its own reference. Release it on the
two edges where the callback is guaranteed not to fire -- submission
failure from tls_server_hello_x509() and a successful
tls_handshake_cancel() -- and at the tail of
svc_tcp_handshake_done() after complete_all().
[cel: rewrote commit message to describe the actual change] |
| Use after free in Microsoft Office Excel allows an unauthorized attacker to disclose information over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: drain bus_reset work on device removal
brcmf_fw_crashed() and the debugfs "reset" entry both schedule
drvr->bus_reset, whose callback recovers drvr through container_of()
and dereferences it. The removal path frees drvr (brcmf_free ->
wiphy_free) without draining the work, so a bus_reset callback pending
or running during removal can outlive drvr.
Cancellation cannot live in brcmf_detach() or brcmf_free(): the work
callback reaches teardown through the bus .reset op (PCIe
brcmf_pcie_reset -> brcmf_detach; SDIO brcmf_sdio_bus_reset ->
brcmf_sdiod_remove -> brcmf_free), so cancelling there would wait for
the running work and deadlock.
Add a per-bus mutex (bus_reset_lock) and route all arming through
brcmf_bus_schedule_reset(), which under the lock skips when the bus is
marked removing. Each bus remove entry calls
brcmf_bus_cancel_reset_work(), which under the same lock sets removing
and cancels the work. Holding the mutex across cancel_work_sync() makes
the set-removing + drain step atomic. Every producer reaches the arming
path from process context -- the PCIe firmware-halt notification runs in
the threaded IRQ handler (brcmf_pcie_isr_thread) and the SDIO hostmail
path runs from the data workqueue -- so the mutex is taken only in
sleepable contexts. Where applicable the remove entry first stops the
firmware-crash producer: on PCIe mask the mailbox and synchronize_irq;
on SDIO unregister the bus interrupt and cancel the data worker, which
also reports firmware halts through brcmf_fw_crashed(). The mutex is
initialized at bus allocation. The SDIO suspend power-off path frees
drvr through the same brcmf_sdiod_remove() and takes the same lock;
resume re-allows the work only on a successful re-probe.
Also guard brcmf_fw_crashed() against a NULL bus_if/drvr: it can fire
before brcmf_attach() wires up drvr, and it dereferences drvr
(bphy_err/brcmf_dev_coredump) before reaching the arming gate.
The bus_reset work is shared across buses, so the drain is applied to
every remove path: PCIe (the .reset op introduced by the Fixes commit),
SDIO (arms the same work through brcmf_fw_crashed()), and USB (via the
debugfs "reset" entry). cancel_work_sync() drains a running or pending
bus_reset work item before removal frees drvr, and patch 1/2 makes the
scratch-buffer release safe when reset teardown has already released
those DMA buffers.
This patch fixes the lifetime of the bus_reset work item itself. It does
not attempt to address the separate, pre-existing lifetime of the
asynchronous firmware completion started by the PCIe reset path. That
callback needs its own lifetime/ownership protocol and is being tracked
separately.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Release the VGA arbiter client on register_device() failure
The re-order in the Fixes commit below displaced vfio_pci_vga_init() as
the last failure point of what is now vfio_pci_core_register_device()
without introducing an unwind for the VGA arbiter registration.
In current kernels this is mostly benign because vfio_pci_set_decode()
only uses pci_dev state, but the original failure path could leave a
callback with a freed vdev cookie. The stale registration also becomes
unsafe again once the callback follows drvdata to the vfio device.
Add the required VGA unwind callout. |
| In the Linux kernel, the following vulnerability has been resolved:
6lowpan: fix NHC entry use-after-free on error path
lowpan_nhc_do_uncompression() looks up an NHC descriptor while holding
lowpan_nhc_lock. If the descriptor has no uncompress callback, the error
path drops the lock before printing nhc->name.
lowpan_nhc_del() removes descriptors under the same lock and then relies
on synchronize_net() before the owning module can be unloaded. That only
waits for net RX RCU readers. lowpan_header_decompress() is also exported
and can be reached from callers that are not necessarily covered by the net
core RX critical section, for example the Bluetooth 6LoWPAN L2CAP receive
path.
This leaves a race where one task drops lowpan_nhc_lock in the error path,
another task unregisters and frees the matching descriptor after
synchronize_net() returns, and the first task then dereferences nhc->name
for the warning.
With the post-unlock window widened, KASAN reports:
BUG: KASAN: slab-use-after-free in lowpan_nhc_do_uncompression+0x1f4/0x220
Read of size 8
lowpan_nhc_do_uncompression
lowpan_header_decompress
Fix this by printing the warning before dropping lowpan_nhc_lock, so the
descriptor name is read while unregister is still excluded. The malformed
packet is still rejected with -ENOTSUPP. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix VF2PF work teardown race in adf_disable_sriov()
The VF2PF interrupt handler queues PF-side response work that stores a
raw pointer to per-VF state (struct adf_accel_vf_info). Currently,
adf_disable_sriov() destroys per-VF mutexes and frees vf_info without
stopping new VF2PF work or waiting for in-flight workers to complete. A
concurrently scheduled or already queued worker can then dereference
freed memory.
This manifests as a use-after-free when KASAN is enabled:
BUG: KASAN: null-ptr-deref in mutex_lock+0x76/0xe0
Write of size 8 at addr 0000000000000260 by task kworker/24:2/...
Workqueue: qat_pf2vf_resp_wq adf_iov_send_resp [intel_qat]
Call Trace:
kasan_report+0x119/0x140
mutex_lock+0x76/0xe0
adf_gen4_pfvf_send+0xd4/0x1f0 [intel_qat]
adf_recv_and_handle_vf2pf_msg+0x290/0x360 [intel_qat]
adf_iov_send_resp+0x8c/0xe0 [intel_qat]
process_one_work+0x6ac/0xfd0
worker_thread+0x4dd/0xd30
kthread+0x326/0x410
ret_from_fork+0x33b/0x670
Add a PF-local flag, vf2pf_disabled, that gates work queueing, worker
processing, and interrupt re-enabling during teardown. Set this flag
atomically with the hardware interrupt mask inside
adf_disable_all_vf2pf_interrupts(). After masking, synchronize the AE
cluster MSI-X interrupt and flush the PF response workqueue before
tearing down per-VF locks and state so all in-flight work completes
before vf_info is destroyed.
Introduce adf_enable_all_vf2pf_interrupts() to clear the flag and
unmask all VF2PF interrupts under the same lock when SR-IOV is
re-enabled. This ensures the software flag and hardware state transition
atomically on both the enable and disable paths. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix UAF in channel timeout by holding conn ref
l2cap_chan_timeout() runs asynchronously and accesses chan->conn. If
the connection is torn down while the timer is running or pending,
chan->conn can be freed, leading to a use-after-free when the timer
worker attempts to lock conn->lock:
| BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:112 [inline]
| BUG: KASAN: slab-use-after-free in atomic_long_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:4456 [inline]
| BUG: KASAN: slab-use-after-free in __mutex_trylock_fast kernel/locking/mutex.c:161 [inline]
| BUG: KASAN: slab-use-after-free in mutex_lock+0x4f/0xa0 kernel/locking/mutex.c:318
| Write of size 8 at addr ffff8881298d9550 by task kworker/2:1/83
|
| CPU: 2 UID: 0 PID: 83 Comm: kworker/2:1 Not tainted 7.1.0-rc6-next-20260601-dirty #6 PREEMPT(full)
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
| Workqueue: events l2cap_chan_timeout
| Call Trace:
| <TASK>
| instrument_atomic_read_write include/linux/instrumented.h:112 [inline]
| atomic_long_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:4456 [inline]
| __mutex_trylock_fast kernel/locking/mutex.c:161 [inline]
| mutex_lock+0x4f/0xa0 kernel/locking/mutex.c:318
| l2cap_chan_timeout+0x5d/0x1b0 net/bluetooth/l2cap_core.c:422
| process_one_work kernel/workqueue.c:3326 [inline]
| process_scheduled_works+0x7c8/0xfb0 kernel/workqueue.c:3409
| worker_thread+0x8a9/0xcf0 kernel/workqueue.c:3490
| kthread+0x346/0x430 kernel/kthread.c:436
| ret_from_fork+0x1a3/0x470 arch/x86/kernel/process.c:158
| ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
| </TASK>
|
| Allocated by task 320:
| l2cap_conn_add+0xa7/0x820 net/bluetooth/l2cap_core.c:7075
| l2cap_connect_cfm+0xdb/0xd70 net/bluetooth/l2cap_core.c:7452
| hci_connect_cfm include/net/bluetooth/hci_core.h:2139 [inline]
| hci_remote_features_evt+0x52f/0x9f0 net/bluetooth/hci_event.c:3760
| hci_event_func net/bluetooth/hci_event.c:7796 [inline]
| hci_event_packet+0x561/0xa70 net/bluetooth/hci_event.c:7847
| hci_rx_work+0x370/0x890 net/bluetooth/hci_core.c:4040
| process_one_work kernel/workqueue.c:3326 [inline]
| process_scheduled_works+0x7c8/0xfb0 kernel/workqueue.c:3409
| worker_thread+0x8a9/0xcf0 kernel/workqueue.c:3490
| kthread+0x346/0x430 kernel/kthread.c:436
| ret_from_fork+0x1a3/0x470 arch/x86/kernel/process.c:158
| ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
|
| Freed by task 322:
| hci_disconn_cfm include/net/bluetooth/hci_core.h:2154 [inline]
| hci_conn_hash_flush+0x101/0x1f0 net/bluetooth/hci_conn.c:2736
| hci_dev_close_sync+0x889/0xde0 net/bluetooth/hci_sync.c:5405
| hci_dev_do_close net/bluetooth/hci_core.c:502 [inline]
| hci_unregister_dev+0x1f7/0x370 net/bluetooth/hci_core.c:2679
| vhci_release+0x12a/0x180 drivers/bluetooth/hci_vhci.c:690
| __fput+0x369/0x890 fs/file_table.c:510
| task_work_run+0x160/0x1d0 kernel/task_work.c:233
| get_signal+0xf5b/0x1120 kernel/signal.c:2810
| arch_do_signal_or_restart+0x4d/0x600 arch/x86/kernel/signal.c:337
| __exit_to_user_mode_loop kernel/entry/common.c:64 [inline]
| exit_to_user_mode_loop+0x85/0x510 kernel/entry/common.c:98
| do_syscall_64+0x263/0x3d0 arch/x86/entry/syscall_64.c:100
| entry_SYSCALL_64_after_hwframe+0x77/0x7f
|
| The buggy address belongs to the object at ffff8881298d9400
| which belongs to the cache kmalloc-512 of size 512
| The buggy address is located 336 bytes inside of
| freed 512-byte region [ffff8881298d9400, ffff8881298d9600)
Fix it by having chan->conn hold a reference to l2cap_conn (via
l2cap_conn_get) when the channel is added to the connection, and
releasing it in the channel destructor. This ensures the l2cap_conn
remains alive as long as the channel exists.
A new FLAG_DEL channel flag is introduced to indicate that the ch
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: igmp: remove multicast group from hash table on device destruction
When a device is destroyed under RTNL, ip_mc_destroy_dev() iterates through
the multicast list and calls ip_ma_put() on each membership, scheduling
them for RCU reclamation. However, they are not unlinked from the device's
multicast hash table (mc_hash).
Since the device remains published in dev->ip_ptr until after
ip_mc_destroy_dev() completes, concurrent RCU readers traversing mc_hash
can still locate and access the multicast group after its refcount is
decremented. If the RCU callback runs and frees the group while a reader is
accessing it, a use-after-free occurs.
Fix this by unlinking the multicast group from mc_hash using
ip_mc_hash_remove() before scheduling it for reclamation.
BUG: KASAN: slab-use-after-free in ip_check_mc_rcu+0x149/0x3f0
Read of size 4 at addr ffff888009bf1408 by task mausezahn/2276
Call Trace:
<IRQ>
dump_stack_lvl+0x67/0x90
print_report+0x175/0x7c0
kasan_report+0x147/0x180
ip_check_mc_rcu+0x149/0x3f0
udp_v4_early_demux+0x36d/0x12d0
ip_rcv_finish_core+0xb8b/0x1390
ip_rcv_finish+0x54/0x120
NF_HOOK+0x213/0x2b0
__netif_receive_skb+0x126/0x340
process_backlog+0x4f2/0xf00
__napi_poll+0x92/0x2c0
net_rx_action+0x583/0xc60
handle_softirqs+0x236/0x7f0
do_softirq+0x57/0x80
</IRQ>
Allocated by task 2239:
kasan_save_track+0x3e/0x80
__kasan_kmalloc+0x72/0x90
____ip_mc_inc_group+0x31a/0xa40
__ip_mc_join_group+0x334/0x3f0
do_ip_setsockopt+0x16fa/0x2010
ip_setsockopt+0x3f/0x90
do_sock_setsockopt+0x1ad/0x300
Freed by task 0:
kasan_save_track+0x3e/0x80
kasan_save_free_info+0x40/0x50
__kasan_slab_free+0x3a/0x60
__rcu_free_sheaf_prepare+0xd4/0x220
rcu_free_sheaf+0x36/0x190
rcu_core+0x8d9/0x12f0
handle_softirqs+0x236/0x7f0 |
