| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() for transmit path header pulls
In vxlan_xmit(), arp_reduce(), and vxlan_mdb_entry_skb_get(), pskb_may_pull() was
being called to verify the availability of network layer headers (ARP, IPv6/ND,
IP/IPv6 MDB keys).
However, during transmit skb->data points to the MAC header, so skb_network_offset(skb)
is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, len) only checks len bytes from skb->data
rather than skb_network_offset(skb) + len, which can leave part of the network header
in non-linear frags.
Replace these remaining pskb_may_pull() calls with pskb_network_may_pull() to properly
account for the MAC header offset. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/dma-iommu: Fix wrong scatterlist length assignment in P2PDMA path
In iommu_dma_map_sg(), when handling PCI P2PDMA cases, the DMA length
of the current scatterlist segment `s` is incorrectly assigned from the
head entry `sg->length` instead of the current entry `s->length`.
This typo causes all P2PDMA segments in the scatterlist to inherit the
length of the first segment, leading to corrupted DMA lengths for multi-
segment scatterlists.
Fix this by using `s->length` instead of `sg->length`. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: validate Add Extended Advertising Data length
MGMT_OP_ADD_EXT_ADV_DATA is registered as a variable-length command,
with MGMT_ADD_EXT_ADV_DATA_SIZE as the fixed header size. The handler
then uses cp->adv_data_len and cp->scan_rsp_len to validate and copy
cp->data, but it never checks that those bytes are part of the mgmt
command payload.
A short command can therefore make add_ext_adv_data() pass an
out-of-bounds pointer into tlv_data_is_valid(). If the bytes beyond
the command buffer are addressable, they can also be copied into the
advertising instance as scan response data, where the caller can read
them back via MGMT_OP_GET_ADV_INSTANCE. The trigger requires
CAP_NET_ADMIN in the initial user namespace; KASAN reports an 8-byte
slab-out-of-bounds read.
Reject commands whose length does not match the fixed header plus both
advertising data lengths before parsing cp->data. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hsr: fix potential OOB access in supervision frame handling
Ensure the entire TLV header is linearized before access by adding
sizeof(struct hsr_sup_tlv) to the pskb_may_pull() calls. Without this,
a truncated frame could cause an out-of-bounds access. |
| In the Linux kernel, the following vulnerability has been resolved:
tunnels: do not assume transport header in iptunnel_pmtud_check_icmp()
In some cases, iptunnel_pmtud_check_icmp() can be called while
skb transport header is not set.
This triggers an out-of-bound access, because
(typeof(skb->transport_header))~0U is 65535.
Access the icmp header based on IPv4 network header,
after making sure icmp->type is present in skb linear part.
Note that iptunnel_pmtud_check_icmpv6()) is fine. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix the out-of-bounds nameoff handling for trailing dirents
Currently we already have boundary-checks for nameoffs, but the trailing
dirents are special since the namelens are calculated with strnlen()
with unchecked nameoffs.
If a crafted EROFS has a trailing dirent with nameoff >= maxsize,
maxsize - nameoff can underflow, causing strnlen() to read past the
directory block.
nameoff0 should also be verified to be a multiple of
`sizeof(struct erofs_dirent)` as well [1].
[1] https://sashiko.dev/#/patchset/20260416063511.3173774-1-hsiangkao%40linux.alibaba.com |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: prevent potential out-of-bounds reads in process_message_header()
If the message frame is (maliciously) corrupted in a way that the
length of the control segment ends up being less than the size of the
message header or a different frame is made to look like a message
frame, out-of-bounds reads may ensue in process_message_header().
Perform an explicit bounds check before decoding the message header. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix potential out-of-bounds read in iwl_mvm_nd_match_info_handler()
The memcpy function assumes the dynamic array notif->matches is at least
as large as the number of bytes to copy. Otherwise, results->matches may
contain unwanted data. To guarantee safety, extend the validation in one
of the checks to ensure sufficient packet length.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix OOB read in smb2_ioctl_query_info QUERY_INFO path
smb2_ioctl_query_info() has two response-copy branches: PASSTHRU_FSCTL
and the default QUERY_INFO path. The QUERY_INFO branch clamps
qi.input_buffer_length to the server-reported OutputBufferLength and then
copies qi.input_buffer_length bytes from qi_rsp->Buffer to userspace, but
it never verifies that the flexible-array payload actually fits within
rsp_iov[1].iov_len.
A malicious server can return OutputBufferLength larger than the actual
QUERY_INFO response, causing copy_to_user() to walk past the response
buffer and expose adjacent kernel heap to userspace.
Guard the QUERY_INFO copy with a bounds check on the actual Buffer
payload. Use struct_size(qi_rsp, Buffer, qi.input_buffer_length)
rather than an open-coded addition so the guard cannot overflow on
32-bit builds. |
| In the Linux kernel, the following vulnerability has been resolved:
usbip: validate number_of_packets in usbip_pack_ret_submit()
When a USB/IP client receives a RET_SUBMIT response,
usbip_pack_ret_submit() unconditionally overwrites
urb->number_of_packets from the network PDU. This value is
subsequently used as the loop bound in usbip_recv_iso() and
usbip_pad_iso() to iterate over urb->iso_frame_desc[], a flexible
array whose size was fixed at URB allocation time based on the
*original* number_of_packets from the CMD_SUBMIT.
A malicious USB/IP server can set number_of_packets in the response
to a value larger than what was originally submitted, causing a heap
out-of-bounds write when usbip_recv_iso() writes to
urb->iso_frame_desc[i] beyond the allocated region.
KASAN confirmed this with kernel 7.0.0-rc5:
BUG: KASAN: slab-out-of-bounds in usbip_recv_iso+0x46a/0x640
Write of size 4 at addr ffff888106351d40 by task vhci_rx/69
The buggy address is located 0 bytes to the right of
allocated 320-byte region [ffff888106351c00, ffff888106351d40)
The server side (stub_rx.c) and gadget side (vudc_rx.c) already
validate number_of_packets in the CMD_SUBMIT path since commits
c6688ef9f297 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle
malicious input") and b78d830f0049 ("usbip: fix vudc_rx: harden
CMD_SUBMIT path to handle malicious input"). The server side validates
against USBIP_MAX_ISO_PACKETS because no URB exists yet at that point.
On the client side we have the original URB, so we can use the tighter
bound: the response must not exceed the original number_of_packets.
This mirrors the existing validation of actual_length against
transfer_buffer_length in usbip_recv_xbuff(), which checks the
response value against the original allocation size.
Kelvin Mbogo's series ("usb: usbip: fix integer overflow in
usbip_recv_iso()", v2) hardens the receive-side functions themselves;
this patch complements that work by catching the bad value at its
source -- in usbip_pack_ret_submit() before the overwrite -- and
using the tighter per-URB allocation bound rather than the global
USBIP_MAX_ISO_PACKETS limit.
Fix this by checking rpdu->number_of_packets against
urb->number_of_packets in usbip_pack_ret_submit() before the
overwrite. On violation, clamp to zero so that usbip_recv_iso() and
usbip_pad_iso() safely return early. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: validate advertising TLV before type checks
tlv_data_is_valid() reads each advertising data field length from
data[i], then inspects data[i + 1] for managed EIR types before
checking that the current field still fits inside the supplied buffer.
A malformed field whose length byte is the last byte of the buffer can
therefore make the parser read one byte past the advertising data.
KASAN reported the following when a malformed MGMT_OP_ADD_ADVERTISING
request reached that path:
BUG: KASAN: vmalloc-out-of-bounds in tlv_data_is_valid()
Read of size 1
Call trace:
tlv_data_is_valid()
add_advertising()
hci_mgmt_cmd()
hci_sock_sendmsg()
Move the existing element-length check before any type-octet inspection
so each non-empty element is proven to contain its type byte before the
parser looks at data[i + 1]. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: control: Validate buf_len before strnlen() in snd_ctl_elem_init_enum_names()
snd_ctl_elem_init_enum_names() advances pointer p through the names
buffer while decrementing buf_len. If buf_len reaches zero but items
remain, the next iteration calls strnlen(p, 0).
While strnlen(p, 0) returns 0 and would hit the existing name_len == 0
error path, CONFIG_FORTIFY_SOURCE's fortified strnlen() first checks
maxlen against __builtin_dynamic_object_size(). When Clang loses track
of p's object size inside the loop, this triggers a BRK exception panic
before the return value is examined.
Add a buf_len == 0 guard at the loop entry to prevent calling fortified
strnlen() on an exhausted buffer.
Found by kernel fuzz testing through Xiaomi Smartphone. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: br_nd_send: validate ND option lengths
br_nd_send() walks ND options according to option-provided lengths.
A malformed option can make the parser advance beyond the computed
option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: Avoid boot crash in RedBoot partition table parser
Given CONFIG_FORTIFY_SOURCE=y and a recent compiler,
commit 439a1bcac648 ("fortify: Use __builtin_dynamic_object_size() when
available") produces the warning below and an oops.
Searching for RedBoot partition table in 50000000.flash at offset 0x7e0000
------------[ cut here ]------------
WARNING: lib/string_helpers.c:1035 at 0xc029e04c, CPU#0: swapper/0/1
memcmp: detected buffer overflow: 15 byte read of buffer size 14
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.19.0 #1 NONE
As Kees said, "'names' is pointing to the final 'namelen' many bytes
of the allocation ... 'namelen' could be basically any length at all.
This fortify warning looks legit to me -- this code used to be reading
beyond the end of the allocation."
Since the size of the dynamic allocation is calculated with strlen()
we can use strcmp() instead of memcmp() and remain within bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/thunderx: Fix possible out-of-bounds string access
Enabling -Wstringop-overflow globally exposes a warning for a common bug
in the usage of strncat():
drivers/edac/thunderx_edac.c: In function 'thunderx_ocx_com_threaded_isr':
drivers/edac/thunderx_edac.c:1136:17: error: 'strncat' specified bound 1024 equals destination size [-Werror=stringop-overflow=]
1136 | strncat(msg, other, OCX_MESSAGE_SIZE);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
...
1145 | strncat(msg, other, OCX_MESSAGE_SIZE);
...
1150 | strncat(msg, other, OCX_MESSAGE_SIZE);
...
Apparently the author of this driver expected strncat() to behave the
way that strlcat() does, which uses the size of the destination buffer
as its third argument rather than the length of the source buffer. The
result is that there is no check on the size of the allocated buffer.
Change it to strlcat().
[ bp: Trim compiler output, fixup commit message. ] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/snapshot: fix dumping of the unaligned regions
The snapshotting code internally aligns data segment to 16 bytes. This
works fine for DPU code (where most of the regions are aligned), but
fails for snapshotting of the DSI data (because DSI data region is
shifted by 4 bytes). Fix the code by removing length alignment and by
accurately printing last registers in the region. While reworking the
code also fix the 16x memory overallocation in
msm_disp_state_dump_regs().
Patchwork: https://patchwork.freedesktop.org/patch/725449/ |
| A flaw was found in libarchive. This vulnerability allows a remote attacker to trigger a heap overflow by providing a specially crafted tar archive. The issue occurs during the parsing of a PAX extended header containing a malformed SUN.holesdata sparse-file attribute. Successful exploitation could lead to a denial of service, making the system unavailable, or potentially allow for arbitrary code execution, giving the attacker control over the affected system. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/net: don't overconsume buffers when using MSG_TRUNC
When a recv/recvmsg is issued with MSG_TRUNC and the incoming packet is
larger than the provided buffer, the net layer returns the full length
of the packet rather than the number of bytes actually copied into the
buffer. As a result, io_uring advances more of the provided buffer ring
than was actually filled. Use the actual filled region size to consume
the buffer, but still return the full size to preserve MSG_TRUNC
semantics.
Take care with multishot, because that seems to already truncate the
consumption based on the available payload size.
This was reported in https://github.com/axboe/liburing/issues/1619.
[axboe: fold in size_t unsigned fix] |
| In the Linux kernel, the following vulnerability has been resolved:
net: mpls: clear inner_protocol when the last label is popped
skb_mpls_push() records the pre-encapsulation network header once, gated
on !skb->inner_protocol. skb_mpls_pop() never clears that record, so it
outlives the encapsulation it describes.
Open vSwitch can then re-push MPLS onto a packet whose
inner_network_header still points at the older, deeper offset: push a
label, pop every label, recirculate (ovs_flow_key_update() re-derives
key->eth.type and resets network_header, but leaves inner_*), then push
again. ovs_fragment() trusts the record:
skb->network_header = skb->inner_network_header;
so skb_network_offset() goes negative. The bound check is signed:
if (skb_network_offset(skb) > MAX_L2_LEN)
a negative offset passes it, and prepare_frag() widens the value:
unsigned int hlen = skb_network_offset(skb);
memcpy(&data->l2_data, skb->data, hlen);
which is a ~4GiB memcpy out of a 30-byte per-CPU buffer.
Reproduced on v7.3-rc1. RDX is the truncated length, (unsigned int)(-8):
BUG: unable to handle page fault for address: ffffe8ffffc16000
#PF: supervisor write access in kernel mode
Oops: 0002 [#1] SMP KASAN NOPTI
RIP: 0010:memcpy+0x8/0x20
RDX: 00000000fffffff8 RSI: ffff888105d732db RDI: ffffe8ffffc16000
prepare_frag+0x3df/0x4e0
ovs_fragment+0x589/0x7e0
do_output+0x4ce/0x5e0
do_execute_actions+0x55d2/0x7b30
ovs_execute_actions+0xea/0x450
Same root-cause shape as commit 975b5b067f52 ("ipv6: sr: restore network
header before routing and forwarding"): a stale network header offset
reaching a consumer that widens it. Here it originates in the MPLS
push/pop path.
Clear inner_protocol once the packet is no longer MPLS, so a later push
re-records the current header. net/sched/act_mpls.c is the only other
skb_mpls_pop() caller and gets the same fix; sch_frag.c saves and
restores inner_protocol around fragmentation in the same way OVS does. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: smbus: reject oversized block transfers in the common path
The SMBus block transfer length data->block[0] is validated in
i2c_smbus_xfer_emulated() but that check runs too late for tracepoints
and is skipped entirely when the adapter provides a native smbus_xfer
implementation. This allows user-controlled oversized block lengths to
reach tracepoint memcpy calls and driver callbacks unchecked.
Add an early validation in __i2c_smbus_xfer() that rejects block
transfers whose caller-supplied length is zero or exceeds
I2C_SMBUS_BLOCK_MAX before any tracepoint fires or driver callback
runs. data->block[0] is filled in by the device on SMBus block reads,
so the check is scoped to operations where the length is actually
supplied by the caller. This is consistent with the existing -EINVAL
convention in the emulated path and protects all downstream consumers
at once: the smbus_write tracepoint, all native smbus_xfer driver
implementations, and the emulated path.
Two distinct bugs are fixed by this change:
Bug 1: smbus_write tracepoint OOB (include/trace/events/smbus.h)
trace_smbus_write() fires before any validation and copies
data->block[0]+1 bytes into a 34-byte event buffer. With
block[0]=0xfe the tracepoint copies 255 bytes, overflowing by 221.
BUG: KASAN: stack-out-of-bounds in trace_event_raw_event_smbus_write+0x27c/0x530
Read of size 255 at addr ffff88800d98fcf8 by task poc_smbus/91
Call Trace:
<TASK>
__asan_memcpy+0x23/0x80
trace_event_raw_event_smbus_write+0x27c/0x530
__i2c_smbus_xfer+0x43a/0xa40
i2c_smbus_xfer+0x19e/0x340
i2cdev_ioctl_smbus+0x38f/0x7f0
i2cdev_ioctl+0x35e/0x680
__x64_sys_ioctl+0x147/0x1e0
do_syscall_64+0xcf/0x15a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Bug 2: i2c-stub I2C_SMBUS_I2C_BLOCK_DATA OOB (drivers/i2c/i2c-stub.c)
stub_xfer() implements .smbus_xfer directly and only clamps
block[0] against 256-command, not I2C_SMBUS_BLOCK_MAX. With
block[0]=0xff and command=0 the loop accesses block[1+i] for
i up to 254, far past the 34-byte union.
UBSAN: array-index-out-of-bounds in drivers/i2c/i2c-stub.c:223:44
index 34 is out of range for type '__u8 [34]'
Call Trace:
<TASK>
__ubsan_handle_out_of_bounds+0xd7/0x120
stub_xfer+0x1971/0x198f [i2c_stub]
__i2c_smbus_xfer+0x306/0xa40
i2c_smbus_xfer+0x19e/0x340
i2cdev_ioctl_smbus+0x38f/0x7f0
i2cdev_ioctl+0x35e/0x680
__x64_sys_ioctl+0x147/0x1e0
do_syscall_64+0xcf/0x15a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Both traces reproduced on v7.0-rc6+i2c/for-current with KASAN+UBSAN. |
