| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wfx: validate MIB read length before copying to caller
wfx_hif_read_mib() copies reply->length bytes from the firmware
response into the caller-provided buffer without checking that
reply->length does not exceed val_len. A firmware response with
a length field larger than expected overruns the caller buffer and
reads past the end of the reply allocation.
Replace the dead -ENOMEM check with an active validation that
reply->length fits within val_len before the memcpy. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_uac1_legacy: validate bRequest index in generic_{set,get}_cmd
generic_set_cmd() and generic_get_cmd() use the low nibble of
ctrl->bRequest as an index into con->data[]:
u8 cmd = (ctrl->bRequest & 0x0F); /* 0 .. 15 */
...
con->data[cmd] = value; /* OOB when cmd >= 5 */
struct usb_audio_control (include/linux/usb/audio.h) declares data as
a 5-element array, so indices 5 through 15 write (or read) up to 44
bytes past the end of the array on the heap.
A malicious USB host can craft a class-specific SET_CUR / GET_CUR
request with an arbitrary bRequest value, triggering the out-of-bounds
access from an IRQ completion handler with no further preconditions.
Add an ARRAY_SIZE() guard to both functions. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ua101: reject mismatched capture/playback packet sizes
detect_usb_format() cross-checks bSubframeSize, bBitResolution and
tSamFreq between the capture and playback interfaces, but never relates
the two endpoints' wMaxPacketSize and bNrChannels. Each playback URB
gets a buffer of ua->playback.max_packet_bytes, while the number of
bytes written into it is derived from the capture stream:
capture_urb_complete() computes frames from the received capture packet
and capture.frame_bytes, and start_usb_playback() and playback_work()
multiply that by playback.frame_bytes.
A device declaring a large capture wMaxPacketSize with few capture
channels and a small playback wMaxPacketSize with many playback channels
therefore memset()s and memcpy()s past the end of the playback buffer,
in open() of the PCM node the driver registers during probe.
usb_submit_urb() rejects the over-long iso_frame_desc[0].length with
-EMSGSIZE, but only after the write.
Reject such descriptors at probe time. Genuine UA-101/UA-1000 hardware
declares proportional packet sizes and is unaffected.
BUG: KASAN: slab-out-of-bounds in start_usb_playback (sound/usb/misc/ua101.c:586)
Write of size 2048 at addr ffff8881098f3c00 by task exploit/5021
Call Trace:
__asan_memset (mm/kasan/shadow.c:84)
start_usb_playback (sound/usb/misc/ua101.c:586)
playback_pcm_open (sound/usb/misc/ua101.c:679)
snd_pcm_open_substream (sound/core/pcm_native.c:2829)
snd_pcm_open (sound/core/pcm_native.c:2865 sound/core/pcm_native.c:2932)
snd_pcm_playback_open (sound/core/pcm_native.c:2891)
snd_open (sound/core/sound.c:166)
chrdev_open (fs/char_dev.c:411)
do_dentry_open (fs/open.c:996)
vfs_open (fs/open.c:1101)
path_openat (fs/namei.c:4837 fs/namei.c:5000)
do_file_open (fs/namei.c:5029)
do_sys_openat2 (fs/open.c:1417)
__x64_sys_openat (fs/open.c:1423 fs/open.c:1439 fs/open.c:1434)
do_syscall_64 (arch/x86/entry/syscall_64.c:61 arch/x86/entry/syscall_64.c:84)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
The buggy address belongs to the object at ffff8881098f3c00
which belongs to the cache kmalloc-192 of size 192
The buggy address is located 0 bytes inside of
allocated 168-byte region [ffff8881098f3c00, ffff8881098f3ca8) |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-multipath: fix underflow in ANA log bounds checks
The number of ANA groups advertised through Identify Controller sizes the
ANA log buffer. The ANA log header and group descriptors independently
supply the number of groups and namespace IDs to parse.
Both bounds checks subtract an untrusted object size from ana_log_size
before comparing the current offset. If the object is larger than the
buffer, the size_t subtraction underflows and lets the parser read beyond
ana_log_buf.
Check the current offset before the first subtraction and compare each
object size with the remaining buffer instead. This rejects inconsistent
ANA data before dereferencing a truncated group descriptor or walking an
oversized namespace ID array. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-auth: fix out-of-bounds write in nvmet_auth_challenge()
nvmet_auth_challenge() receives its output buffer as a void pointer.
sizeof(*d) therefore evaluates to one with GCC and undercounts the fixed
challenge header by 15 bytes. A short AUTH_RECEIVE buffer can pass the
check before the challenge is copied past the end of its allocation.
Use the typed challenge pointer when calculating the response size.
BUG: KASAN: slab-out-of-bounds in nvmet_execute_auth_receive (drivers/nvme/target/fabrics-cmd-auth.c:442 drivers/nvme/target/fabrics-cmd-auth.c:569)
Write of size 32 by task kworker/1:1H/64
Workqueue: nvmet_tcp_wq nvmet_tcp_io_work
Call Trace:
nvmet_execute_auth_receive (drivers/nvme/target/fabrics-cmd-auth.c:442 drivers/nvme/target/fabrics-cmd-auth.c:569)
nvmet_tcp_try_recv_pdu (drivers/nvme/target/tcp.c:1119 drivers/nvme/target/tcp.c:1243)
nvmet_tcp_io_work (drivers/nvme/target/tcp.c:1350 drivers/nvme/target/tcp.c:1382 drivers/nvme/target/tcp.c:1445)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3405 kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
The buggy address is located 16 bytes inside of
allocated 33-byte region [ffff888000554e80, ffff888000554ea1)
Kernel panic - not syncing: KASAN: panic_on_warn set ... |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: minstrel_ht: validate fixed rate index
The fixed_rate_idx debugfs file is a plain u32 attribute, so any value
can be written to it. minstrel_ht_update_stats() then copies the value
into mi->max_tp_rate[] and mi->max_prob_rate, and
minstrel_ht_set_rate() uses MI_RATE_GROUP()/MI_RATE_IDX() to index
minstrel_mcs_groups[] (42 entries) and mi->groups[].rates[] (10 entries)
with it.
Writing e.g. 65535 selects group 4095 and rate index 15, far outside
both arrays. The out-of-bounds entries are dereferenced and updated as
struct minstrel_rate_stats (retry counts, etc.), so the invalid index
corrupts adjacent kernel memory. With CONFIG_UBSAN_BOUNDS the access is
reported as an array-index-out-of-bounds in minstrel_ht_set_rate().
Only a valid group/rate pair, or U32_MAX to disable fixed rate
processing, can be used safely, so reject any other value when the
debugfs file is written.
The file is only reachable through a root-only debugfs mount, so this is
not a privilege boundary. The out-of-bounds access is still a bug that
must not be reachable through a writable debugfs attribute. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use one headroom snapshot for neighbour replies
vxlan_na_create() samples LL_RESERVED_SPACE() to size the reply skb and then
samples it again to reserve headroom. A concurrent vxlan_changelink() can
update needed_headroom between the two reads, creating a TOCTOU race. The
second value can exceed the allocation and make the Ethernet header write out
of bounds.
The race is reproducible on the unpatched kernel. It occurred when
vxlan_na_create() generated a neighbour reply while vxlan_changelink() changed
the link headroom. KASAN caught a four-byte write two bytes beyond a 704-byte
skbuff_small_head allocation.
Snapshot the headroom once and use that value for both allocation and
reservation. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipconfig: bound DHCP option construction
ic_dhcp_init_options() appends the hostname (option 12), vendor-class
(option 60) and client-ID (option 61) options into the fixed 312-byte
bootp_pkt.exten[] buffer. Only the client-ID branch checked the
remaining space; the hostname and vendor-class writes were unbounded.
A 64-byte hostname together with the maximum 252-byte dhcpclass=
identifier needs 18 + (2 + 64) + (2 + 252) = 338 of the 312 available
bytes even before the terminating END marker, so the vendor-class memcpy
runs past the end of exten[]. With CONFIG_FORTIFY_SOURCE this is
reported as a field-spanning write and, when the kernel is booted with
panic_on_warn=1, aborts boot with a panic.
Route the optional options through a common helper that makes sure the
option, its 2-byte header and the END marker all fit and drops an option
that would not. Configurations with short options keep sending exactly
the same bytes as before. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: mgmt: fix race in read_unconf_index_list()
read_unconf_index_list() counts unconfigured controllers before allocating
its response, then checks the device flags again while filling it.
hci_dev_list_lock stabilizes list membership, but it does not serialize the
per-device flags. During asynchronous controller setup, the worker can set
HCI_UNCONFIGURED and clear HCI_SETUP between the two passes. A controller
omitted from the allocation count can then become eligible for the fill
pass, causing an out-of-bounds write to rp->index[].
Allocate space for every device on hci_dev_list. Since list membership
cannot change while hci_dev_list_lock is held, the response remains large
enough regardless of flag transitions. The reported count and response
length still include only eligible unconfigured controllers. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Clamp implicit feedback packet count to URB capacity
data_ep_set_params() allocates each data URB for exactly u->packets
isochronous frames, so urb->iso_frame_desc[] has u->packets slots and
ctx->packets is the driver's only record of that limit. For an implicit
feedback sink, snd_usb_queue_pending_output_urbs() overwrites it with the
sync source's packet count, which is calculated independently from the
capture endpoint's parameters. When that count is larger,
prepare_playback_urb() and prepare_silent_urb() can write
iso_frame_desc[] past the allocation; their existing bounds limit payload
bytes, not the descriptor index.
The reproducer uses a high-speed UAC2 device declaring bInterval 1 for
implicit feedback capture (8 packets) and bInterval 4 for playback
(1 packet). On the first capture completion after the stream starts, it
accesses seven descriptors spanning 112 bytes beyond the one-packet URB:
BUG: KASAN: slab-out-of-bounds in prepare_playback_urb (sound/usb/pcm.c:1560)
Write of size 4 at addr ffff88801e696ad0 by task vhci_rx/178
prepare_playback_urb (sound/usb/pcm.c:1560)
prepare_outbound_urb (sound/usb/endpoint.c:340)
snd_usb_queue_pending_output_urbs (sound/usb/endpoint.c:501)
snd_complete_urb (sound/usb/endpoint.c:1834)
__usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1657)
usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1741)
vhci_rx_loop (drivers/usb/usbip/vhci_rx.c:107)
kthread (kernel/kthread.c:436)
The buggy address belongs to the object at ffff88801e696a00
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 0 bytes to the right of
allocated 208-byte region [ffff88801e696a00, ffff88801e696ad0)
Record the allocated packet count per endpoint and clamp both the adopted
count and the packet-size copy to it. Fold the Format Type II delimiter
into urb_packs before the allocation loop so the recorded limit matches
every URB. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix heap overflow in DACL owner/group rewrite
When id_mode_to_cifs_acl rewrites an existing DACL, it allocates a
buffer sized according to the on-disk DACL length reported by
dacl_ptr->size. However, replace_sids_and_copy_aces may rewrite each
ACE with a new owner/group SID obtained from the cifs.idmap upcall.
Those SIDs can have up to SID_MAX_SUB_AUTHORITIES (15) sub-authorities,
making each ACE up to 76 bytes (sizeof(struct smb_ace)).
If the original DACL contains short SIDs (e.g., 1 sub-authority) while
the replacement SIDs are long, the rewritten ACEs overflow the
allocation.
Fix this by always budgeting for worst-case SID expansion: allocate
sizeof(struct smb_acl) plus num_aces * sizeof(struct smb_ace), which
covers the smb_acl header and room for every ACE at maximum SID size.
This replaces the previous split logic that used dacl_ptr->size for
cifsacl mounts but num_aces * sizeof(struct smb_ace) for mode_from_sid
mounts: both paths can trigger the same rewrite and need the same
headroom.
KASAN reports this as:
BUG: KASAN: slab-out-of-bounds in build_sec_desc+0x1e8a/0x2680 [cifs]
Write of size 4 at addr ffff8881a5e25374 by task chown/5298
...
The buggy address is located 0 bytes to the right of
allocated 884-byte region [ffff8881a5e25000, ffff8881a5e25374) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Bound VP index against VP_CTRL IOCB bitmap size
The VP control IOCB selects its target virtual port by setting one bit
in vp_idx_map, a fixed 16-byte (128-bit) array in both
vp_ctrl_entry_24xx and vp_ctrl_entry_24xx_ext. qla25xx_ctrlvp_iocb()
computes map = (vp_index - 1) / 8 and writes vce->vp_idx_map[map]
without checking that map stays within the array.
max_npiv_vports is taken from firmware and only sanitized to a
MIN_MULTI_ID_FABRIC-aligned boundary, so it can legitimately be 191 or
255, and qla24xx_control_vp() only rejects vp_index >= max_npiv_vports.
A vp_index above 128 therefore yields map >= 16 and an out-of-bounds
write of up to 16 bytes past vp_idx_map, corrupting the trailing IOCB
fields (or the adjacent request-ring slot on the 64-byte layout).
Reject a vp_index that cannot be represented in the IOCB bitmap in
qla24xx_control_vp(), and add a defensive ARRAY_SIZE() guard in
qla25xx_ctrlvp_iocb() before the write. Adapters that report the usual
63 or 127 NPIV vports are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: reject duplicate wiphy cipher suite entries
Duplicate entries in wiphy->cipher_suites do not describe any
additional capability, but cfg80211 currently accepts them and leaves
individual consumers to deal with them.
One such consumer is the WEXT compatibility code, which appends a WEP
key length for each WEP cipher entry it sees. Repeated WEP entries can
therefore overflow the fixed iw_range::encoding_size array returned by
SIOCGIWRANGE.
Reject duplicate cipher suite entries in wiphy_register() instead.
This keeps the cipher suite invariant in one place and makes malformed
wiphy descriptions fail early with -EINVAL, rather than relying on a
single cfg80211 user to handle duplicates correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate and share PSP fw_pri_buf copies via psp_copy_fw
Change psp_copy_fw from void to int: return -ENODEV when drm_dev_enter
fails, and -EINVAL when the image size is zero or larger than the
1 MiB PSP private buffer.
Replace open-coded memset/memcpy into fw_pri_buf with psp_copy_fw. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Bound GPIO I2C table entry count from VBIOS
Reject undersized tables and cap the derived entry count
to AMDGPU_MAX_I2C_BUS so we do not overrun adev->i2c_bus[]
or walk an absurd number of entries on corrupt size fields. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix buffer overflow during vBIOS update
Clamp the buffer postion to write by setting the bin attribute
to the maximum buffer size so that VFS layer will block the
out-of-bounds accessing. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix out-of-bounds tid_data access in BA notif
mvmsta->tid_data was indexed by the TFD loop counter 'i' instead of
the actual TID value 'tid'. This writes lq_color into a random tid_data
slot unrelated to the BA entry.
Since multi-TID blockack is not really in use, 'i' was always 0 and no
harm was done.
Add a out-of-bound check before accessing the array. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Zero queue and stack outputs on lock failure
Queue and stack pop/peek helpers accept an uninitialized output buffer
because the verifier expects the helper to initialize it. The empty-map
error path clears the buffer, but a failed lock acquisition returns
-EBUSY without writing it.
Clear the output before returning -EBUSY so BPF programs cannot observe
uninitialized stack contents after a failed helper call. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: fix max_qid race between configfs and controller allocation
The function nvmet_subsys_attr_qid_max_store() can race against
nvmet_alloc_ctrl() when a subsystem's max_qid limit is modified.
Suppose max_qid is currently 64. If nvmet_alloc_ctrl() executes:
ctrl->sqs = kzalloc_objs(struct nvmet_sq *, subsys->max_qid + 1);
and at this exact point, a userspace process changes max_qid to 128,
nvmet_subsys_attr_qid_max_store() will set the new max_qid value. It
attempts to delete active controllers to force a reconnect, but the
new controller won't be deleted because it hasn't been added to the
subsys->ctrls list yet.
nvmet_alloc_ctrl() then proceeds and adds the new controller to the
subsys->ctrls list. Later, when nvmet_install_queue() is called, it
will see max_qid set to 128, but the memory allocated for sqs is only
sized for 64 entries. This results in a KASAN out-of-bounds warning
and potential memory corruptions.
Fix this by protecting the queue allocations and list insertion in
nvmet_alloc_ctrl() with down_read(&nvmet_config_sem). Because
nvmet_subsys_attr_qid_max_store() acquires down_write(&nvmet_config_sem)
to modify the attribute, this safely prevents the configfs writer from
modifying max_qid during controller creation.
Copy the max_qid from the subsystem to the controller's structure
during the allocation; ctrl->max_qid never changes as long as the
controller remains in LIVE state, so this will prevent similar race
conditions. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix memory corruption by not reinjecting CK machine checks
Channel-subsystem damage machine checks are for the host channel
subsystem. The guest channel subsystem is emulated in the userspace VMM.
There is no point in forwarding such machine checks into the guest.
This also simplifies the machine check reinjection and avoids kfree of a
stack variable as reported by sashiko. There might be still machine
checks that have the ck bit set with another bit (like instruction
damage), mask out the CK bit in s390_backup_mcck_info(), like the CP and
ED bits already are. |
