| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: anx7411 - stop the IRQ before destroying the workqueue
The IRQ is devm-managed, so it can still queue plat->work while
remove() is tearing the queue down. Disable it first. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: dwc2: shut down wakeup timer before freeing HCD state
dwc2_wakeup_detected() accesses the DWC2 host state and can rearm the
wakeup timer. dwc2_hcd_free() currently deletes the timer only after
freeing host-owned state, and timer_delete() does not synchronize a
callback or prevent it from being queued again.
Stop and shut down the timer in dwc2_hcd_release(), before the HCD
resources are freed. This covers both the HCD initialization error path
and normal HCD removal. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: fix saved termios reset race
Resetting saved termios state on device registration is needed where a
minor number can be reused for an entirely different device and where
the old settings may prevent the port from even being opened (e.g. when
CLOCAL is not set).
Not all TTY drivers guarantee that the minor number is no longer in use
when registering devices however, something which can lead to a
use-after-free when closing a TTY (and saving its termios) races with
re-registration.
Add a new TTY_DRIVER_RESET_SAVED_TERMIOS flag to request that any saved
termios state is reset on registration and only set it for drivers that
make sure that the minor number is no longer in use. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: max3100: shut down timer before freeing port
max3100_shutdown() stops the polling timer but returns early during
system suspend. If the SPI device is unbound before resume, the serial
core does not call max3100_shutdown() again, so max3100_remove() frees
the port while the timer remains armed. max3100_timeout() may then
access the freed port and re-arm the timer.
Add final timer teardown to max3100_remove() and use
timer_shutdown_sync() to prevent a racing callback from re-arming it.
Also free the IRQ and destroy the workqueue there before freeing the
port. Keep timer_delete_sync() in max3100_shutdown() so that a
subsequent open() can re-arm the timer.
The workqueue is created before request_irq() and destroyed on both
request_irq() failure and normal shutdown. Its presence at remove thus
identifies the IRQ left registered when suspend bypasses shutdown.
Free the IRQ before destroying the workqueue, in both
max3100_shutdown() and max3100_remove(), and cancel the pending work
in between. free_irq() waits for a running interrupt handler to
finish and no new handler can start afterwards, so a racing handler
cannot queue work on a workqueue that is being destroyed; the
force_end_work check in max3100_dowork() only narrows that window, as
a handler delayed between the check and queue_work() could still run
after the teardown has cleared the workqueue pointer. Cancelling the
work also keeps destroy_workqueue() from waiting on a queued work item
in case remove() ever runs while the freezable workqueue is still
frozen, e.g. device removal during the resume window, before
workqueues are thawed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_bcm7271: fix use-after-free in brcmuart_remove()
brcmuart_handle_irq() starts priv->hrt to work around a receive-timeout
quirk of the 8250 core when hardware flow control is enabled; the timer
callback brcmuart_hrtimer_func() dereferences priv.
brcmuart_remove() cancels the hrtimer before it unregisters the port, so
a receive-timeout interrupt that arrives in between re-arms the timer.
After devm frees priv, the callback runs on freed memory.
Unregister the port before cancelling the hrtimer.
serial8250_unregister_port() shuts the port down and frees its IRQ, so
brcmuart_handle_irq() can no longer restart the timer, and the final
hrtimer_cancel() drains any timer that was armed before or during the
unregister.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Serialize compat port-info ioctls
The native sequencer ioctl path serializes handler calls with
client->ioctl_mutex, but the translated port-info compat path invokes the
same handlers through snd_seq_kernel_client_ctl() without taking that
mutex.
This lets concurrent compat CREATE_PORT requests pass the port-count
check before any request reaches the serialized insertion. The computed
integer port index can then exceed the address field range and wrap to an
existing index. Subsequent subscriber teardown can resolve the duplicate
address to the wrong port and access a freed subscriber.
Take ioctl_mutex while dispatching converted port-info requests, matching
the native ioctl path. All translated port-info commands share this
helper, so their accesses to the client port state are serialized as
well. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize fragmented ISO packet queueing
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn->data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: count only matching reservations in reserved switch
ieee80211_vif_use_reserved_switch() validates a replacement by counting
assigned links on ctx->replace_ctx and treating reservations too
broadly. A link can still be assigned to the old channel context while
holding a reservation that belongs to a different replacement
operation.
That can make the current replacement appear complete too early. If
another link finalizes first, the function can free the
WILL_BE_REPLACED chanctx while the unmatched link and driver still use
it, leading to a use-after-free in later beacon generation.
Require an in-place reservation to point at the current replacement
context, and require the reserved and assigned contexts to be the
matching replacement pair, before counting or moving the link. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: keep paired old chanctx alive
An in-place replacement keeps reciprocal replace_ctx pointers between
the old WILL_BE_REPLACED chanctx and the new REPLACES_OTHER chanctx.
However, the early free paths only consider assigned and reserved link
users when deciding whether to free the old chanctx.
That lets the old chanctx be freed too early while the replacement
partner still points back to it, either when the last assigned link is
released or when that link successfully reassigns to another existing
context. Later unreserve and switch-finalization paths can then follow a
stale replace_ctx pointer.
Keep a paired old chanctx alive until the replacement pair has been torn
down. Apply the same check to both __ieee80211_link_release_channel()
and ieee80211_link_use_reserved_reassign(). If the replacement is later
abandoned, ieee80211_link_unreserve_chanctx() already tears down the
pairing before freeing the old chanctx once no users remain. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix driver deregistration order
USB serial driver modules register one driver for the USB bus and one or
more drivers for the ports on the USB serial bus.
When unloading a driver module, the USB driver must be deregistered
before the USB serial bus drivers so that I/O is stopped before
unbinding the ports to avoid use-after-free in completion handlers
accessing port data.
Note that the "new_id" attributes must first be removed to prevent new
ids from being added and triggering a probe of the USB driver after it
has been deregistered. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix KASAN reported use-after-free when request is canceled
Alan reported that when doing stress testing sometimes KASAN notices
use-after-free during control channel operation (stripped down keeping
the relevant parts):
BUG: KASAN: slab-use-after-free in tb_cfg_request_sync+0x240/0x250 [thunderbolt]
Read of size 24 at addr ffff88811067f290 by task kworker/u40:2/1760
<TASK>
tb_cfg_request_sync+0x240/0x250 [thunderbolt]
tb_cfg_read_raw+0x367/0x510 [thunderbolt]
tb_cfg_read+0xec/0x240 [thunderbolt]
tb_port_get_link_generation+0x258/0x420 [thunderbolt]
tb_usb3_consumed_bandwidth+0x1c1/0x2c0 [thunderbolt]
tb_tunnel_consumed_bandwidth+0xfd/0x910 [thunderbolt]
tb_available_bandwidth+0x5f2/0xeb0 [thunderbolt]
tb_recalc_estimated_bandwidth+0x2a0/0x1bc0 [thunderbolt]
tb_handle_dp_bandwidth_request+0x1897/0x5e20 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 1760:
__kmalloc_cache_noprof+0x1ee/0x550
tb_cfg_read_raw+0x1d3/0x510 [thunderbolt]
tb_cfg_read+0xec/0x240 [thunderbolt]
tb_port_get_link_generation+0x258/0x420 [thunderbolt]
tb_usb3_consumed_bandwidth+0x1c1/0x2c0 [thunderbolt]
tb_tunnel_consumed_bandwidth+0xfd/0x910 [thunderbolt]
tb_available_bandwidth+0x5f2/0xeb0 [thunderbolt]
tb_recalc_estimated_bandwidth+0x2a0/0x1bc0 [thunderbolt]
tb_handle_dp_bandwidth_request+0x1897/0x5e20 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
Freed by task 926:
kfree+0x18f/0x4a0
tb_cfg_request_put+0xb7/0xe0 [thunderbolt]
tb_cfg_request_work+0x82/0x120 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
Second to last potentially related work creation:
__queue_work+0x575/0xd00
queue_work_on+0x77/0x80
tb_cfg_request_cancel+0xc7/0x260 [thunderbolt]
tb_cfg_request_sync+0x1f6/0x250 [thunderbolt]
tb_cfg_read_raw+0x367/0x510 [thunderbolt]
tb_cfg_read+0xec/0x240 [thunderbolt]
tb_port_get_link_generation+0x258/0x420 [thunderbolt]
tb_usb3_consumed_bandwidth+0x1c1/0x2c0 [thunderbolt]
tb_tunnel_consumed_bandwidth+0xfd/0x910 [thunderbolt]
tb_available_bandwidth+0x5f2/0xeb0 [thunderbolt]
tb_recalc_estimated_bandwidth+0x2a0/0x1bc0 [thunderbolt]
tb_handle_dp_bandwidth_request+0x1897/0x5e20 [thunderbolt]
process_one_work+0x675/0x1230
worker_thread+0x5e6/0xf70
kthread+0x365/0x470
ret_from_fork+0x54d/0x710
ret_from_fork_asm+0x1a/0x30
The last stack trace is helpful because it shows that we are cancelling
a request and looking at tb_cfg_request_cancel() what might happen is
that tb_cfg_request_work() completes right before tb_cfg_request_cancel()
starts and because of this it will call schedule_work() queueing the
same work to run again. However, it is already removed from the
request_queue and reference count is dropped so when
tb_cfg_request_work() triggers again it will access memory that is
already released.
Fix this so that we first make sure a cancelled request is not handed
away from tb_cfg_request_find() or scheduled to run. Then instead of
relying on the worker to clean up the request we will do it in
tb_cfg_request_cancel() after the work is canceled from running. Make
tb_cfg_request_dequeue() release the request only if it was actually
removed from the queue. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: xilinx-xadc: free IRQ before cancelling the unmask worker on unbind
The ZYNQ XADC alarm IRQ handler queues zynq_unmask_work via
schedule_delayed_work(); that work is cleared by a devm callback.
Register the devm callback before devm_request_irq() so the devres LIFO
teardown frees the IRQ first, ensuring the handler can no longer queue
work by the time the workqueue is cleared. Otherwise the handler could
re-arm the work and run it after the xadc structure has been freed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: gp2ap020a00f: drain irq_work after free_irq
The threaded IRQ handler queues data->work through irq_work_queue() so
the trigger is polled from a per-CPU context. free_irq() does not flush
an irq_work the handler already queued, so after gp2ap020a00f_remove()
returns that work may still run and call iio_trigger_poll() on data->trig,
which the devm cleanup has already freed, causing a use-after-free.
Add irq_work_sync(&data->work) after free_irq() in remove() and in the
probe error path, mirroring commit 78601726d4a5 ("iio: trigger: sysfs:
fix use-after-free on remove").
Found by an in-house static analysis tool, confirmed by manual review. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: trigger: cancel reenable_work before freeing trigger
iio_trigger_notify_done_atomic() defers ->reenable() into
trig->reenable_work on the system workqueue, and the worker dereferences
the owning trigger through container_of(). Nothing cancels this work
before iio_trig_release() frees the trigger, so a worker armed by the
last in-flight IRQ can outlive the free and touch freed memory.
Cancel it at the top of iio_trig_release(), which every free path
reaches through the device core's final put_device().
Found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix next_buffer UAF and NextCommand bounds in compound PDUs
Fix several related bounds checking and pointer lifecycle issues in
receive_encrypted_standard()'s handling of compound encrypted frames:
- Clear next_buffer after assigning it to server->bigbuf. A stale
next_buffer pointer can lead to a use-after-free on subsequent
error paths.
- Update pdu_length to the decrypted plaintext size (buf_size). Using
the pre-decryption length allows NextCommand to point into stale
ciphertext residue.
- Reject next_cmd values smaller than MID_HEADER_SIZE(server).
- Fix an integer overflow in the upper bound check by verifying
pdu_length - next_cmd < MID_HEADER_SIZE(server), ensuring the
trailing slice is large enough for a header. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btqcomsmd: destroy RPMsg endpoints before freeing hci_dev
The command and ACL RPMsg endpoints store struct btqcomsmd as their
callback private data. The receive callbacks dereference btq->hdev
without taking an hci_dev reference.
The current teardown order frees the hci_dev before destroying the RPMsg
endpoints in both the hci_register_dev() error path and the driver remove
path. If WCNSS delivers data in that window, the endpoint callback can
run with an already freed hci_dev and pass it to the Bluetooth core.
For qcom_smd endpoints, rpmsg_destroy_ept() closes the channel and clears
the callback under the channel recv_lock. The receive path holds the same
lock while invoking the callback, so destroying the endpoints first both
prevents new callbacks and serializes with any callback already running.
Destroy the command and ACL endpoints before hci_free_dev(). Keep
hci_unregister_dev() first during remove so the HCI core stops issuing
operations before the transport endpoints are shut down. In the full
registration-error cleanup path, return directly after freeing the hci_dev
to avoid falling through to the partial-construction labels and destroying
the endpoints twice. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: cttimeout: prevent UAF during module unload
nf_ct_set_timeout() protects the timeout hook dereference and policy lookup
with rcu_read_lock(). cttimeout_exit(), however, unregisters the per-net
operations before it clears the hook.
This allows the following interleaving:
CPU 0 CPU 1
cttimeout_exit() nf_ct_set_timeout()
unregister_pernet_subsys() rcu_read_lock()
kfree(pernet) h = nf_ct_timeout_hook
h->timeout_find_get()
nfct_timeout_pernet()
The hook still points to ctnl_timeout_find_get() when CPU 1 looks up the
already freed per-net timeout list. KASAN reported:
BUG: KASAN: slab-use-after-free in ctnl_timeout_find_get
Read of size 8 by task poc/90
Call Trace:
ctnl_timeout_find_get+0x271/0x2a0 [nfnetlink_cttimeout]
nf_ct_set_timeout+0x7b/0x3c0
xt_ct_tg_check+0x724/0xb20
xt_check_target+0x234/0xa90
do_ipt_set_ctl+0x570/0x1270
Allocated by task 89:
__kmalloc_noprof+0x16e/0x460
ops_init+0x6d/0x420
register_pernet_operations+0x2f6/0x670
Freed by task 91:
kfree+0x131/0x390
ops_undo_list+0x3d4/0x730
unregister_pernet_operations+0x232/0x490
unregister_pernet_subsys+0x1c/0x30
cttimeout_exit+0x52/0x970 [nfnetlink_cttimeout]
Clear the hook and wait for existing readers before unregistering the
per-net operations. This blocks new policy lookups and ensures readers that
observed the hook finish before the per-net storage is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Skip vport under deletion in report ID acquisition
qla24xx_report_id_acquisition() format-1 handling walks ha->vp_list under
vport_slock, takes a vref_count on the matching vport and calls
qla_update_host_map() to register its port id.
A vport teardown via qla24xx_vport_delete() sets VPORT_DELETE, then
qla24xx_disable_vp() removes the vport from the host_map btree and zeroes
vha->d_id (RESET_AL_PA). The vport is only unlinked from vp_list later,
in qla24xx_deallocate_vp_id(), which clears vp_map[idx] (RESET_VP_IDX)
but does not touch host_map. In the window in between, report ID
acquisition can still find the vport on vp_list and call
qla_update_host_map(); with d_id already zeroed it takes the
btree_insert32() path and re-inserts the dying vport into host_map.
Nothing cleans that entry afterwards, so once scsi_host_put() frees the
vha a later host_map lookup dereferences freed memory.
Skip a vport that has VPORT_DELETE set before taking the reference, so it
is neither re-registered nor scheduled for DPC re-registration. This
mirrors the existing guard in qla2x00_alert_all_vps(). |
| In the Linux kernel, the following vulnerability has been resolved:
virt: acrn: Fix irqfd use-after-free during eventfd shutdown
acrn_irqfd_deassign() and the eventfd EPOLLHUP wakeup can race and free
the same struct hsm_irqfd:
CPU0 CPU1
---- ----
eventfd_release()
wake_up_poll(EPOLLHUP)
hsm_irqfd_wakeup()
queue_work(&irqfd->shutdown)
acrn_irqfd_deassign()
hsm_irqfd_shutdown()
list_del_init()
eventfd_ctx_remove_wait_queue()
eventfd_ctx_put()
kfree(irqfd)
hsm_irqfd_shutdown_work()
container_of(work, ..., shutdown)
irqfd->vm <-- use-after-free
The deassign path freed the irqfd while a shutdown work item was
already queued by EPOLLHUP (or vice versa), so the work item could
resurrect a dangling pointer through container_of().
Switch to the lifetime model used by KVM irqfds:
- Deassign/deinit only deactivate the irqfd: remove it from vm->irqfds
under irqfds_lock and queue the cleanup work.
- hsm_irqfd_shutdown_work() becomes the sole owner that unhooks the
eventfd waitqueue entry, drops the eventfd reference and frees the
irqfd.
- A new HSM_IRQFD_FLAG_SHUTDOWN bit guarded by test_and_set_bit()
ensures the cleanup work is queued at most once, no matter how many
of {EPOLLHUP, deassign, deinit} fire concurrently. This is safe to
call from the waitqueue callback, which runs with wqh->lock held and
IRQs disabled and therefore cannot take irqfds_lock.
- acrn_irqfd_deassign() flushes vm->irqfd_wq before returning so the
eventfd is fully detached on return. acrn_irqfd_deinit() deactivates
every irqfd, flushes the workqueue and only then destroys it, so no
path can queue_work() onto a torn-down workqueue.
- acrn_irqfd_assign() now installs the eventfd waitqueue entry and
publishes the irqfd to vm->irqfds under irqfds_lock, so the irqfd is
never visible to deassign/deinit before its waitqueue entry is in
place, and any EPOLLHUP that fires in the assign window queues
cleanup work that blocks on irqfds_lock until publication is done. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/xive: propagate IPI init errors to prevent use-after-free
When xive_init_ipis() fails (e.g. irq_domain_alloc_irqs() fails),
the error path frees the global xive_ipis array. However,
xive_smp_probe() previously ignored this failure and proceeded to
call xive_setup_cpu_ipi(), which dereferences the already-freed
xive_ipis pointer -- a use-after-free.
Now that xive_smp_probe() returns int (previous patch), propagate
the error from xive_init_ipis() and xive_setup_cpu_ipi() through
xive_smp_probe(). Check the return value in both pnv_smp_probe()
and pSeries_smp_probe() so that IPI setup is aborted cleanly on
failure, avoiding the use-after-free. |
