| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: avoid reading already updated pages during GC
We found the following issue during fuzz testing:
page: refcount:3 mapcount:0 mapping:00000000b6e89c65 index:0x18b2dc pfn:0x161ba9
memcg:f8ffff800e269c00
aops:f2fs_meta_aops ino:2
flags: 0x52880000000080a9(locked|waiters|uptodate|lru|private|zone=1|kasantag=0x4a)
raw: 52880000000080a9 fffffffec6e17588 fffffffec0ccc088 a7ffff8067063618
raw: 000000000018b2dc 0000000000000009 00000003ffffffff f8ffff800e269c00
page dumped because: VM_BUG_ON_FOLIO(folio_test_uptodate(folio))
page_owner tracks the page as allocated
post_alloc_hook+0x58c/0x5ec
prep_new_page+0x34/0x284
get_page_from_freelist+0x2dcc/0x2e8c
__alloc_pages_noprof+0x280/0x76c
__folio_alloc_noprof+0x18/0xac
__filemap_get_folio+0x6bc/0xdc4
pagecache_get_page+0x3c/0x104
do_garbage_collect+0x5c78/0x77a4
f2fs_gc+0xd74/0x25f0
gc_thread_func+0xb28/0x2930
kthread+0x464/0x5d8
ret_from_fork+0x10/0x20
------------[ cut here ]------------
kernel BUG at mm/filemap.c:1563!
folio_end_read+0x140/0x168
f2fs_finish_read_bio+0x5c4/0xb80
f2fs_read_end_io+0x64c/0x708
bio_endio+0x85c/0x8c0
blk_update_request+0x690/0x127c
scsi_end_request+0x9c/0xb8c
scsi_io_completion+0xf0/0x250
scsi_finish_command+0x430/0x45c
scsi_complete+0x178/0x6d4
blk_mq_complete_request+0xcc/0x104
scsi_done_internal+0x214/0x454
scsi_done+0x24/0x34
which is similar to the problem reported by syzbot:
https://syzkaller.appspot.com/bug?extid=3686758660f980b402dc
This case is consistent with the description in commit 9bf1a3f
("f2fs: avoid GC causing encrypted file corrupted"):
Page 1 is moved from blkaddr A to blkaddr B by move_data_block, and after
being written it is marked as uptodate. Then, Page 1 is moved from blkaddr
B to blkaddr C, VM_BUG_ON_FOLIO was triggered in the endio initiated by
ra_data_block.
There is no need to read Page 1 again from blkaddr B, since it has already
been updated. Therefore, avoid initiating I/O in this case. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix data loss caused by incorrect use of nat_entry flag
Data loss can occur when fsync is performed on a newly created file
(before any checkpoint has been written) concurrently with a checkpoint
operation. The scenario is as follows:
create & write & fsync 'file A' write checkpoint
- f2fs_do_sync_file // inline inode
- f2fs_write_inode // inode folio is dirty
- f2fs_write_checkpoint
- f2fs_flush_merged_writes
- f2fs_sync_node_pages
- f2fs_flush_nat_entries
- f2fs_fsync_node_pages // no dirty node
- f2fs_need_inode_block_update // return false
SPO and lost 'file A'
f2fs_flush_nat_entries() sets the IS_CHECKPOINTED and HAS_LAST_FSYNC
flags for the nat_entry, but this does not mean that the checkpoint has
actually completed successfully. However, f2fs_need_inode_block_update()
checks these flags and incorrectly assumes that the checkpoint has
finished.
The root cause is that the semantics of IS_CHECKPOINTED and
HAS_LAST_FSYNC are only guaranteed after the checkpoint write fully
completes.
This patch modifies f2fs_need_inode_block_update() to acquire the
sbi->node_write lock before reading the nat_entry flags, ensuring that
once IS_CHECKPOINTED and HAS_LAST_FSYNC are observed to be set, the
checkpoint operation has already completed. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/psi: fix race between file release and pressure write
A potential race condition exists between pressure write and cgroup file
release regarding the priv member of struct kernfs_open_file, which
triggers the uaf reported in [1].
Consider the following scenario involving execution on two separate CPUs:
CPU0 CPU1
==== ====
vfs_rmdir()
kernfs_iop_rmdir()
cgroup_rmdir()
cgroup_kn_lock_live()
cgroup_destroy_locked()
cgroup_addrm_files()
cgroup_rm_file()
kernfs_remove_by_name()
kernfs_remove_by_name_ns()
vfs_write() __kernfs_remove()
new_sync_write() kernfs_drain()
kernfs_fop_write_iter() kernfs_drain_open_files()
cgroup_file_write() kernfs_release_file()
pressure_write() cgroup_file_release()
ctx = of->priv;
kfree(ctx);
of->priv = NULL;
cgroup_kn_unlock()
cgroup_kn_lock_live()
cgroup_get(cgrp)
cgroup_kn_unlock()
if (ctx->psi.trigger) // here, trigger uaf for ctx, that is of->priv
The cgroup_rmdir() is protected by the cgroup_mutex, it also safeguards
the memory deallocation of of->priv performed within cgroup_file_release().
However, the operations involving of->priv executed within pressure_write()
are not entirely covered by the protection of cgroup_mutex. Consequently,
if the code in pressure_write(), specifically the section handling the
ctx variable executes after cgroup_file_release() has completed, a uaf
vulnerability involving of->priv is triggered.
Therefore, the issue can be resolved by extending the scope of the
cgroup_mutex lock within pressure_write() to encompass all code paths
involving of->priv, thereby properly synchronizing the race condition
occurring between cgroup_file_release() and pressure_write().
And, if an live kn lock can be successfully acquired while executing
the pressure write operation, it indicates that the cgroup deletion
process has not yet reached its final stage; consequently, the priv
pointer within open_file cannot be NULL. Therefore, the operation to
retrieve the ctx value must be moved to a point *after* the live kn
lock has been successfully acquired.
In another situation, specifically after entering cgroup_kn_lock_live()
but before acquiring cgroup_mutex, there exists a different class of
race condition:
CPU0: write memory.pressure CPU1: write cgroup.pressure=0
=========================== =============================
kernfs_fop_write_iter()
kernfs_get_active_of(of)
pressure_write()
cgroup_kn_lock_live(memory.pressure)
cgroup_tryget(cgrp)
kernfs_break_active_protection(kn)
... blocks on cgroup_mutex
cgroup_pressure_write()
cgroup_kn_lock_live(cgroup.pressure)
cgroup_file_show(memory.pressure, false)
kernfs_show(false)
kernfs_drain_open_files()
cgroup_file_release(of)
kfree(ctx)
of->priv = NULL
cgroup_kn_unlock()
... acquires cgroup_mutex
ctx = of->priv; // may now be NULL
if (ctx->psi.trigger) // NULL dereference
Consequently, there is a possibility that of->priv is NULL, the pressure
write needs to check for this.
Now that the scope of the cgroup_mutex has been expanded, the original
explicit cgroup_get/put operations are no longer necessary, this is
because acquiring/releasing the live kn lock inherently executes a
cgroup get/put operation.
[1]
BUG: KASAN: slab-use-after-free in pressure_write+0xa4/0x210 kernel/cgroup/cgroup.c:4011
Call Trace:
pressure_write+0xa4/0x210 kernel/cgroup/cgroup.c:4011
cgroup_file_write+0x36f/0x790 kernel/cgroup/cgroup.c:43
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix BUG_ON in __ceph_build_xattrs_blob() due to stale blob size
The generic/642 test-case can reproduce the kernel crash:
[40243.605254] ------------[ cut here ]------------
[40243.605956] kernel BUG at fs/ceph/xattr.c:918!
[40243.607142] Oops: invalid opcode: 0000 [#1] SMP PTI
[40243.608067] CPU: 7 UID: 0 PID: 498762 Comm: kworker/7:1 Not tainted 7.0.0-rc7+ #3 PREEMPT(full)
[40243.609700] Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[40243.611820] Workqueue: ceph-msgr ceph_con_workfn
[40243.612715] RIP: 0010:__ceph_build_xattrs_blob+0x1b8/0x1e0
[40243.613731] Code: 0f 84 82 fe ff ff e9 cf 8e 56 ff 48 8d 65 e8 31 c0 5b 41 5c 41 5d 5d 31 d2 31 c9 31 f6 31 ff 45 31 c0 45 31 c9 c3 cc cc cc cc <0f> 0b 4c 8b 62 08 41 8b 85 24 07 00 00 49 83 c4 04 41 89 44 24 fc
[40243.616888] RSP: 0018:ffffcc80c4d4b688 EFLAGS: 00010287
[40243.617773] RAX: 0000000000010026 RBX: 0000000000000001 RCX: 0000000000000000
[40243.618928] RDX: ffff8a773798dee0 RSI: 0000000000000000 RDI: 0000000000000000
[40243.620158] RBP: ffffcc80c4d4b6a0 R08: 0000000000000000 R09: 0000000000000000
[40243.621573] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a75f3b58000
[40243.622907] R13: ffff8a75f3b58000 R14: 0000000000000080 R15: 000000000000bffd
[40243.624054] FS: 0000000000000000(0000) GS:ffff8a787d1b4000(0000) knlGS:0000000000000000
[40243.625331] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[40243.626269] CR2: 000072f390b623c0 CR3: 000000011c02a003 CR4: 0000000000372ef0
[40243.627408] Call Trace:
[40243.627839] <TASK>
[40243.628188] __prep_cap+0x3fd/0x4a0
[40243.628789] ? do_raw_spin_unlock+0x4e/0xe0
[40243.629474] ceph_check_caps+0x46a/0xc80
[40243.630094] ? __lock_acquire+0x4a2/0x2650
[40243.630773] ? find_held_lock+0x31/0x90
[40243.631347] ? handle_cap_grant+0x79f/0x1060
[40243.632068] ? lock_release+0xd9/0x300
[40243.632696] ? __mutex_unlock_slowpath+0x3e/0x340
[40243.633429] ? lock_release+0xd9/0x300
[40243.634052] handle_cap_grant+0xcf6/0x1060
[40243.634745] ceph_handle_caps+0x122b/0x2110
[40243.635415] mds_dispatch+0x5bd/0x2160
[40243.636034] ? ceph_con_process_message+0x65/0x190
[40243.636828] ? lock_release+0xd9/0x300
[40243.637431] ceph_con_process_message+0x7a/0x190
[40243.638184] ? kfree+0x311/0x4f0
[40243.638749] ? kfree+0x311/0x4f0
[40243.639268] process_message+0x16/0x1a0
[40243.639915] ? sg_free_table+0x39/0x90
[40243.640572] ceph_con_v2_try_read+0xf58/0x2120
[40243.641255] ? lock_acquire+0xc8/0x300
[40243.641863] ceph_con_workfn+0x151/0x820
[40243.642493] process_one_work+0x22f/0x630
[40243.643093] ? process_one_work+0x254/0x630
[40243.643770] worker_thread+0x1e2/0x400
[40243.644332] ? __pfx_worker_thread+0x10/0x10
[40243.645020] kthread+0x109/0x140
[40243.645560] ? __pfx_kthread+0x10/0x10
[40243.646125] ret_from_fork+0x3f8/0x480
[40243.646752] ? __pfx_kthread+0x10/0x10
[40243.647316] ? __pfx_kthread+0x10/0x10
[40243.647919] ret_from_fork_asm+0x1a/0x30
[40243.648556] </TASK>
[40243.648902] Modules linked in: overlay hctr2 libpolyval chacha libchacha adiantum libnh libpoly1305 essiv intel_rapl_msr intel_rapl_common intel_uncore_frequency_common skx_edac_common nfit kvm_intel kvm irqbypass joydev ghash_clmulni_intel aesni_intel rapl input_leds mac_hid psmouse vga16fb serio_raw vgastate floppy i2c_piix4 pata_acpi bochs qemu_fw_cfg i2c_smbus sch_fq_codel rbd dm_crypt msr parport_pc ppdev lp parport efi_pstore
[40243.654766] ---[ end trace 0000000000000000 ]---
Commit d93231a6bc8a ("ceph: prevent a client from exceeding the MDS
maximum xattr size") moved the required_blob_size computation to before
the __build_xattrs() call, introducing a race.
__build_xattrs() releases and reacquires i_ceph_lock during execution.
In that window, handle_cap_grant() may update i_xattrs.blob with a
newer MDS-provided blob and bump i_xattrs.version. When
__bui
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: don't set EXT4_GET_BLOCKS_CONVERT when splitting before submitting I/O
When allocating blocks during within-EOF DIO and writeback with
dioread_nolock enabled, EXT4_GET_BLOCKS_PRE_IO was set to split an
existing large unwritten extent. However, EXT4_GET_BLOCKS_CONVERT was
set when calling ext4_split_convert_extents(), which may potentially
result in stale data issues.
Assume we have an unwritten extent, and then DIO writes the second half.
[UUUUUUUUUUUUUUUU] on-disk extent U: unwritten extent
[UUUUUUUUUUUUUUUU] extent status tree
|<- ->| ----> dio write this range
First, ext4_iomap_alloc() call ext4_map_blocks() with
EXT4_GET_BLOCKS_PRE_IO, EXT4_GET_BLOCKS_UNWRIT_EXT and
EXT4_GET_BLOCKS_CREATE flags set. ext4_map_blocks() find this extent and
call ext4_split_convert_extents() with EXT4_GET_BLOCKS_CONVERT and the
above flags set.
Then, ext4_split_convert_extents() calls ext4_split_extent() with
EXT4_EXT_MAY_ZEROOUT, EXT4_EXT_MARK_UNWRIT2 and EXT4_EXT_DATA_VALID2
flags set, and it calls ext4_split_extent_at() to split the second half
with EXT4_EXT_DATA_VALID2, EXT4_EXT_MARK_UNWRIT1, EXT4_EXT_MAY_ZEROOUT
and EXT4_EXT_MARK_UNWRIT2 flags set. However, ext4_split_extent_at()
failed to insert extent since a temporary lack -ENOSPC. It zeroes out
the first half but convert the entire on-disk extent to written since
the EXT4_EXT_DATA_VALID2 flag set, but left the second half as unwritten
in the extent status tree.
[0000000000SSSSSS] data S: stale data, 0: zeroed
[WWWWWWWWWWWWWWWW] on-disk extent W: written extent
[WWWWWWWWWWUUUUUU] extent status tree
Finally, if the DIO failed to write data to the disk, the stale data in
the second half will be exposed once the cached extent entry is gone.
Fix this issue by not passing EXT4_GET_BLOCKS_CONVERT when splitting
an unwritten extent before submitting I/O, and make
ext4_split_convert_extents() to zero out the entire extent range
to zero for this case, and also mark the extent in the extent status
tree for consistency. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix e4b bitmap inconsistency reports
A bitmap inconsistency issue was observed during stress tests under
mixed huge-page workloads. Ext4 reported multiple e4b bitmap check
failures like:
ext4_mb_complex_scan_group:2508: group 350, 8179 free clusters as
per group info. But got 8192 blocks
Analysis and experimentation confirmed that the issue is caused by a
race condition between page migration and bitmap modification. Although
this timing window is extremely narrow, it is still hit in practice:
folio_lock ext4_mb_load_buddy
__migrate_folio
check ref count
folio_mc_copy __filemap_get_folio
folio_try_get(folio)
......
mb_mark_used
ext4_mb_unload_buddy
__folio_migrate_mapping
folio_ref_freeze
folio_unlock
The root cause of this issue is that the fast path of load_buddy only
increments the folio's reference count, which is insufficient to prevent
concurrent folio migration. We observed that the folio migration process
acquires the folio lock. Therefore, we can determine whether to take the
fast path in load_buddy by checking the lock status. If the folio is
locked, we opt for the slow path (which acquires the lock) to close this
concurrency window.
Additionally, this change addresses the following issues:
When the DOUBLE_CHECK macro is enabled to inspect bitmap-related
issues, the following error may be triggered:
corruption in group 324 at byte 784(6272): f in copy != ff on
disk/prealloc
Analysis reveals that this is a false positive. There is a specific race
window where the bitmap and the group descriptor become momentarily
inconsistent, leading to this error report:
ext4_mb_load_buddy ext4_mb_load_buddy
__filemap_get_folio(create|lock)
folio_lock
ext4_mb_init_cache
folio_mark_uptodate
__filemap_get_folio(no lock)
......
mb_mark_used
mb_mark_used_double
mb_cmp_bitmaps
mb_set_bits(e4b->bd_bitmap)
folio_unlock
The original logic assumed that since mb_cmp_bitmaps is called when the
bitmap is newly loaded from disk, the folio lock would be sufficient to
prevent concurrent access. However, this overlooks a specific race
condition: if another process attempts to load buddy and finds the folio
is already in an uptodate state, it will immediately begin using it without
holding folio lock. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: do not keep dest_dst if dev is going down
There is race between the netdev notifier ip_vs_dst_event()
and the code that caches dst with dev that is going down.
As the FIB can be notified for the closed device after our
handler finishes, it is possible valid route to be returned
and cached resuling in a leaked dev reference until the dest
is not removed.
To prevent new dest_dst to be attached to dest just after the
handler dropped the old one, add a netif_running() check
to make sure the notifier handler is not currently running
for device that is closing. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down PASID entry
The Intel VT-d Scalable Mode PASID table entry consists of 512 bits (64
bytes). When tearing down an entry, the current implementation zeros the
entire 64-byte structure immediately using multiple 64-bit writes.
Since the IOMMU hardware may fetch these 64 bytes using multiple
internal transactions (e.g., four 128-bit bursts), updating or zeroing
the entire entry while it is active (P=1) risks a "torn" read. If a
hardware fetch occurs simultaneously with the CPU zeroing the entry, the
hardware could observe an inconsistent state, leading to unpredictable
behavior or spurious faults.
Follow the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the PASID entry.
2. Use a dma_wmb() to ensure the cleared bit is visible to hardware
before proceeding.
3. Execute the required invalidation sequence (PASID cache, IOTLB, and
Device-TLB flush) to ensure the hardware has released all cached
references.
4. Only after the flushes are complete, zero out the remaining fields
of the PASID entry.
Also, add a dma_wmb() in pasid_set_present() to ensure that all other
fields of the PASID entry are visible to the hardware before the Present
bit is set. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_queue: do shared-unconfirmed check before segmentation
Ulrich reports a regression with nfqueue:
If an application did not set the 'F_GSO' capability flag and a gso
packet with an unconfirmed nf_conn entry is received all packets are
now dropped instead of queued, because the check happens after
skb_gso_segment(). In that case, we did have exclusive ownership
of the skb and its associated conntrack entry. The elevated use
count is due to skb_clone happening via skb_gso_segment().
Move the check so that its peformed vs. the aggregated packet.
Then, annotate the individual segments except the first one so we
can do a 2nd check at reinject time.
For the normal case, where userspace does in-order reinjects, this avoids
packet drops: first reinjected segment continues traversal and confirms
entry, remaining segments observe the confirmed entry.
While at it, simplify nf_ct_drop_unconfirmed(): We only care about
unconfirmed entries with a refcnt > 1, there is no need to special-case
dying entries.
This only happens with UDP. With TCP, the only unconfirmed packet will
be the TCP SYN, those aren't aggregated by GRO.
Next patch adds a udpgro test case to cover this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not ASSERT() when the fs flips RO inside btrfs_repair_io_failure()
[BUG]
There is a bug report that when btrfs hits ENOSPC error in a critical
path, btrfs flips RO (this part is expected, although the ENOSPC bug
still needs to be addressed).
The problem is after the RO flip, if there is a read repair pending, we
can hit the ASSERT() inside btrfs_repair_io_failure() like the following:
BTRFS info (device vdc): relocating block group 30408704 flags metadata|raid1
------------[ cut here ]------------
BTRFS: Transaction aborted (error -28)
WARNING: fs/btrfs/extent-tree.c:3235 at __btrfs_free_extent.isra.0+0x453/0xfd0, CPU#1: btrfs/383844
Modules linked in: kvm_intel kvm irqbypass
[...]
---[ end trace 0000000000000000 ]---
BTRFS info (device vdc state EA): 2 enospc errors during balance
BTRFS info (device vdc state EA): balance: ended with status: -30
BTRFS error (device vdc state EA): parent transid verify failed on logical 30556160 mirror 2 wanted 8 found 6
BTRFS error (device vdc state EA): bdev /dev/nvme0n1 errs: wr 0, rd 0, flush 0, corrupt 10, gen 0
[...]
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
------------[ cut here ]------------
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
kernel BUG at fs/btrfs/bio.c:938!
Oops: invalid opcode: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 868 Comm: kworker/u8:13 Tainted: G W N 6.19.0-rc6+ #4788 PREEMPT(full)
Tainted: [W]=WARN, [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Workqueue: btrfs-endio simple_end_io_work
RIP: 0010:btrfs_repair_io_failure.cold+0xb2/0x120
RSP: 0000:ffffc90001d2bcf0 EFLAGS: 00010246
RAX: 0000000000000051 RBX: 0000000000001000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8305cf42 RDI: 00000000ffffffff
RBP: 0000000000000002 R08: 00000000fffeffff R09: ffffffff837fa988
R10: ffffffff8327a9e0 R11: 6f69747265737361 R12: ffff88813018d310
R13: ffff888168b8a000 R14: ffffc90001d2bd90 R15: ffff88810a169000
FS: 0000000000000000(0000) GS:ffff8885e752c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
------------[ cut here ]------------
[CAUSE]
The cause of -ENOSPC error during the test case btrfs/124 is still
unknown, although it's known that we still have cases where metadata can
be over-committed but can not be fulfilled correctly, thus if we hit
such ENOSPC error inside a critical path, we have no choice but abort
the current transaction.
This will mark the fs read-only.
The problem is inside the btrfs_repair_io_failure() path that we require
the fs not to be mount read-only. This is normally fine, but if we are
doing a read-repair meanwhile the fs flips RO due to a critical error,
we can enter btrfs_repair_io_failure() with super block set to
read-only, thus triggering the above crash.
[FIX]
Just replace the ASSERT() with a proper return if the fs is already
read-only. |
| In the Linux kernel, the following vulnerability has been resolved:
mpls: add seqcount to protect the platform_label{,s} pair
The RCU-protected codepaths (mpls_forward, mpls_dump_routes) can have
an inconsistent view of platform_labels vs platform_label in case of a
concurrent resize (resize_platform_label_table, under
platform_mutex). This can lead to OOB accesses.
This patch adds a seqcount, so that we get a consistent snapshot.
Note that mpls_label_ok is also susceptible to this, so the check
against RTA_DST in rtm_to_route_config, done outside platform_mutex,
is not sufficient. This value gets passed to mpls_label_ok once more
in both mpls_route_add and mpls_route_del, so there is no issue, but
that additional check must not be removed. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: defer tunnel netdev_put to RCU release
ovs_netdev_tunnel_destroy() may run after NETDEV_UNREGISTER already
detached the device. Dropping the netdev reference in destroy can race
with concurrent readers that still observe vport->dev.
Do not release vport->dev in ovs_netdev_tunnel_destroy(). Instead, let
vport_netdev_free() drop the reference from the RCU callback, matching
the non-tunnel destroy path and avoiding additional synchronization
under RTNL. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: prevent immediate PASID reuse case
PASID resue could cause interrupt issue when process
immediately runs into hw state left by previous
process exited with the same PASID, it's possible that
page faults are still pending in the IH ring buffer when
the process exits and frees up its PASID. To prevent the
case, it uses idr cyclic allocator same as kernel pid's.
(cherry picked from commit 8f1de51f49be692de137c8525106e0fce2d1912d) |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio with a
larger queue depth against nvmet-pci-epf:
arm-smmu-v3 fc900000.iommu: 0x0000010000000010
arm-smmu-v3 fc900000.iommu: 0x0000020000000000
arm-smmu-v3 fc900000.iommu: 0x000000090000f040
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: event: F_TRANSLATION client: 0000:01:00.0 sid: 0x100 ssid: 0x0 iova: 0x90000f040 ipa: 0x0
arm-smmu-v3 fc900000.iommu: unpriv data write s1 "Input address caused fault" stag: 0x0
Flush the write by performing a readl() of the same address to ensure that
the write has reached the destination before the ATU entry is unmapped.
The same problem was solved for dw_pcie_ep_raise_msi_irq() in commit
8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping"), but there
it was solved by dedicating an outbound iATU only for MSI. We can't do the
same for MSI-X because each vector can have a different msg_addr and the
msg_addr may be changed while the vector is masked.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: unconditionally bump set->nelems before insertion
In case that the set is full, a new element gets published then removed
without waiting for the RCU grace period, while RCU reader can be
walking over it already.
To address this issue, add the element transaction even if set is full,
but toggle the set_full flag to report -ENFILE so the abort path safely
unwinds the set to its previous state.
As for element updates, decrement set->nelems to restore it.
A simpler fix is to call synchronize_rcu() in the error path.
However, with a large batch adding elements to already maxed-out set,
this could cause noticeable slowdown of such batches. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: Don't process extts if PTP is disabled
The ice_ptp_extts_event() function can race with ice_ptp_release() and
result in a NULL pointer dereference which leads to a kernel panic.
Panic occurs because the ice_ptp_extts_event() function calls
ptp_clock_event() with a NULL pointer. The ice driver has already
released the PTP clock by the time the interrupt for the next external
timestamp event occurs.
To fix this, modify the ice_ptp_extts_event() function to check the
PTP state and bail early if PTP is not ready. |
| In the Linux kernel, the following vulnerability has been resolved:
selinux: fix BPF token permission checks
Avoid multiple lookups of the bpffs creator SID using the token's file
descriptor when the same information can be found via the resolved
path/dentry (in selinux_bpf_token_create()) or the token itself (in
selinux_bpf_map_create() and selinux_bpf_prog_load()). Not only does
this simplify the code, it avoids potential TOCTOU issues if the user
changes the token file descriptor passed into the kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
namei: don't reveal overmounted entries in refwalk
In rcuwalk the dentry is validated before it is accepted. step_into()
step_into() rechecks d_seq and __follow_mount_rcu() rechecks mount_lock.
An entry that gets unlinked in between causes the lookup to retry and
miss.
A refwalk doesn't do this. lookup_fast() takes a reference on the hashed
dentry and simply accepts it. So an unlink that happens after the
reference was taken isn't seen by refwalk. That's fine for a simple
file. We just happened to open it before it was unlinked, no problem.
For a mountpoint and specifically a locked mountpoint it very much
isn't. The unlink detaches all mounts and then removes the name. Any
refwalk that hasn't traversed the mounts yet simply reveals the
underlying entry. It's a very narrow window but it can be hit:
reads of a covered file in 60 s, 3 walkers, ~15000 unlinks
no widening 27
that step + 200 us 3741
See the appended patch for a more reliable reproducer.
So check the entry after step_into(). unlink(), rmdir() and rename()
mark the dentry with dont_mount() before they detach the mounts and
remove the dentry.
So a dentry that is marked with DCACHE_CANT_MOUNT and is unhashed by the
time its mounts were looked at is a name that was unlinked under the
refwalk. DCACHE_CANT_MOUNT is read after the mounts were looked up and
it is set before they are detached by detach_mounts(). A refwalk that
missed the mounts will see DCACHE_CANT_MOUNT.
Plain d_unlinked() is fine. A rename takes the dentry off its hash chain
but ___d_drop() leaves d_hash.pprev set. So only __d_drop() and a rename
over the dentry unhash it. The only move that flips IS_ROOT splices in a
disconnected alias. That doesn't have DCACHE_CANT_MOUNT set.
Add the to step_into_slowpath(). ".." and LOOKUP_DOWN may legitimately
land on an unhashed directory. A refwalk that crossed onto a mount has
path.mnt different from nd->path.mnt. A dentry that a filesystem dropped
on its own (d_invalidate(), d_drop()) doesn't have the flag set and is
treated as before.
// SPDX-License-Identifier: GPL-2.0
/*
* unlink_covered: unlink a file that is a mountpoint in a detached copy of
* its mount, against walkers that open it through that copy.
*
* A is a tmpfs with the file f1 (content SECRET_F) and the plain file
* MARK_A. A' is an open_tree(OPEN_TREE_CLONE) copy of A with MARK_A bound
* on A'/f1, held through an O_PATH fd on its root once the tree fd is
* closed. Walkers open f1 through that fd while the driver unlinks A/f1,
* where nothing is mounted on it. A walker may read MARK_A or get ENOENT.
* A read of SECRET_F is a hit: the name was found after its mount was
* gone. The lockless walks use openat2(RESOLVE_CACHED).
*
* usage: unlink_covered [-t seconds] [-w walkers]
*/
#ifndef _GNU_SOURCE
#define _GNU_SOURCE
#endif
#include <errno.h>
#include <fcntl.h>
#include <pthread.h>
#include <stdatomic.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#include <sys/mount.h>
#include <sys/stat.h>
#include <sys/syscall.h>
#include <linux/openat2.h>
#ifndef __NR_open_tree
#define __NR_open_tree 428
#endif
#ifndef __NR_move_mount
#define __NR_move_mount 429
#endif
#ifndef __NR_openat2
#define __NR_openat2 437
#endif
#ifndef OPEN_TREE_CLONE
#define OPEN_TREE_CLONE 1
#endif
#ifndef OPEN_TREE_CLOEXEC
#define OPEN_TREE_CLOEXEC O_CLOEXEC
#endif
#ifndef MOVE_MOUNT_F_EMPTY_PATH
#define MOVE_MOUNT_F_EMPTY_PATH 0x00000004
#endif
#define WORK "/tmp/uc"
#define ADIR WORK "/A"
static int duration = 60, nwalkers = 3;
static atomic_int stop, writer_waiting;
static pthread_rwlock_t cur_lock = PTHREAD_RWLOCK_INITIALIZER;
static int cur_fd = -1; /* the root of A', -1 while there is none */
static atomic_long n_unlink, n_walk, n_mark, n_enoent, n_othe
---truncated--- |
| Time-of-check time-of-use (toctou) race condition in Reliable Multicast Transport Driver (RMCAST) allows an authorized attacker to elevate privileges locally. |
